Cirrus Design was founded by brothers Alan and Dale Klapmeier, Cirrus Design began as a kit airplane design and manufacturing company in Baraboo, Wisconsin in 1984. Though the first airplane designed was not FAA certified, it became the inspiration for developing technologically advanced production aircraft. In 1994, the corporation moved its headquarters to larger facilities in Duluth, Minnesota, and began research and development of the SR20, a four-passenger, single-engine composite aircraft.
Offered the SR20 four-seat composites light monoplane (first flown March 1995), for delivery to customers from 1999.
Era
Cirrus Aero Engines Ltd
Cirrus engines were originally built by ADC Aircraft until Cirrus Aero Engines Limited was formed in 1927.
The company became Cirrus Hermes in 1931 when it was bought by the Cirrus-Hermes Engineering Company and later became the Cirrus Engine Section of Blackburn & General Aircraft Limited in 1934, and operated as a separate division until production ended in the post-World War II era.
Cirrus’s first product was the 90 hp (67 kW) Cirrus I, which passed its 50 hour type rating in 1925. It was the first air-cooled inline engine, a design that proved extremely popular for light aircraft. The basic layout was quickly copied by a number of other manufacturers. Later versions named the Cirrus II, and Cirrus III were produced each with slightly greater displacement, and power.
After purchase by Hermes the Cirrus Hermes I, II, III & IV were produced ranging in power from 105 hp to 140 hp depending on type. The later Cirrus engines were designed to run inverted.
Circa Reproductions ONW / Beamcraft

The ONW/ Beamcraft I is a version of a design built in the 1960s. It uses commercial window frame “Beams” for the body, and simple 1 inch tubes for the tail. The wings are a simple ladder structure with strut bracing. It can be built in High wing, Mid wing or Low wing configuration, and nose or tail wheel. It is intended for engines ranging from 16 Horse Kohler or Briggs to the 447 rotax and will fly delightfully in the US UL range.
The TNW/ Beamcraft II is a biplane version of the Beam Craft: Same structure, same wheel arrangements, same rough weights and performance. You can have 2 ailerons or 4.

Beamcraft I
Wingspan: 28 ft
Wing Area: 126.5 sq. ft.
Length: 15 ft 66 in
Height: (various)
Weight: 250 lbs
Fuel Tank: 5 US gal.
Stall: 25 mph
Cruise: 50-65 mph
Top Speed: 65 mph
Never Exceed: 75 mph
Gross wt: 500 lbs
G Factor: 5.7+ 2.8-
Beamcraft II
Wingspan: 24 ft
Wing Area: 144 sq. ft.
Circa Reproductions Miranda

Named after Graham Lee’s Granddaughter, it is a small negative stagger Sesquiplane, constructed of Aluminum tube and fabric. Miranda is a very light cabin job, designed for efficiency in touring and fun. The small chord lower wing improves total lift. Whittman wing tips boost top speed and climb; shorten take off and reduce stall speed. A large diameter prop gives the plane STOL performance, while the short wing span Allows steep decent angles for excellent short field performance.
Miranda can be powered with a Rotax 277 to 582, VW, Hirth or most motors between 28 and 65 horse. Extremely versatile.
Wingspan: 22 ft
Wing Area: 117 sq. ft.
Length: 17 ft 8 in
Height: 7 ft 6 in
Weight: 280 lbs
Fuel Tank: 10 US gal.
Stall: 30 mph
Cruise: 70-90 mph
Top Speed: 100+ mph
Never Exceed: 125 mph
Gross wt: 600 lbs
G Factor: 5.7+ 2.8-
Circa Reproductions Sopwith Tabloid / Baby

This is a 2 plane set of plans. You can combine the desireable aspects of both. The Tabloid was produced first as a Bennet racer, and did very well. It was then adopted by the military. With all of the accessories added, it needed a bigger engine, a change of cowl, and rudder to become the Sopwith Baby. Both aircraft were 2 place side by side, but in 7/8 scale they are perfect for the average 200 pound pilot of today. The Sopwith’s construction techniques are similar to the Nieuports. The fuselage can be built in a couple of weekends, and wing ribs will only take a couple of hours to bend.
Best Performance (Baby) Rotax 582 or Hirth with 72 inch or larger prop. The Tabloid can be VW powered due to the smaller cowl, but will need a 2100 CC Or larger engine.
NOTE: The skids are necessary with the rearward placed wheels. The wheels can be positioned as on the baby without tip over skids.
Sopwith Tabloid and Baby
Wingspan: 21 ft 75 in
Wing Area: 195 sq. ft.
Length: 19 ft 5 in
Height: 7 ft 43 in
Weight: 325 lbs
Fuel Tank: 12 – 15 US gal.
Stall: 35 mph
Cruise: 75 mph
Top Speed: 90 mph
Never Exceed: 110 mph
Gross wt: 650 lbs
G Factor: 5.7+ 2.8-
Circa Reproductions Morane Saulnier N / Bullet

The Morane Saulnier N or Bullet is an earlier WW1 Design, one of the first to have a gun that fired through the propeller requiring deflector plates on the propeller. This Shoulder wing design was faster than anything around at the time despite being wire braced.
The replica is constructed just like the Nieuport, of tubes and gussets, but has the addition of 1/8 plywood formers and stringers to round out the fuselage. Builders could forego the formers and change the tail to produce a Pfalz (the German variant). The Morane replica has proper ailerons, as they did on the later models, and the flying stabilator can be split into stab and elevator. It flew well either way.
Best Performance with Rotax or Hirth ~ 500cc 2.5 or 3:1 reduction. VW is possible, but performance will suffer appreciably in acceleration and climb due to short propeller diameter. Rotax 503 will swing a 72 X 33 or 68 X 34 and really perform. VW’s will swing 60 or 61 inch @ 3000 RPM with just over Half the thrust.
Wingspan: 23 ft 10 in
Wing Area: 117.5
Length: 19 ft 3 in
Height: ~6 ft
Weight: ~275 lbs empty
Fuel Tank: Up to 12 US gal.
Stall: mid 30’s
Cruise: mid 70’s
Top Speed: 100+
Never Exceed: 115
Gross wt.: 600 lbs
G Factor: 5.7+ 2.8-
Circa Reproductions Nieuport 24

Circa Reproductions Nieuport 17

Plans from Canadian Graham Lee who had re drawn the original drawings down to the 7/8 scale. The Nieuport 17 is all aluminium construction, covered with a polysynthetic fabric and painted with aircraft finishes. Powered by an 1835cc VW engine that has been fitted with a starter motor, it cruises at a leisurely 65 70 mph.
A CIRCA Reproduction Nieuport 11/17 features 6061 tube, pop rivet construction. Average cost in 2008 was $6,000.00.
Engine: 1835cc VW 60HP
Span: 21’5″
Length: 16’5″
Empty Weight: 300 LBS
Useful Load: 300 LBS
Wing Area: 114 SQ. FT.
Seats: 1
Take Off Distance: 250 FT
Stall: 33 MPH
Landing Speed: very slow
Cruise: 80 MPH
Rate Of Climb: 650 FPM
Engine: VW1600.
Wing span: 22 ft.
Length: 16 ft.
Height: 6 ft 6 in.
Weight: 362 lb.
Max speed: 70 mph.
Endurance: 4 hr.
Circa Reproductions Nieuport 12

The 87% scale replica of a Nieuport 12 was designed and prototyped in 1989, at Oshkosh ‘90, it took 3rd place in the light plane category.
The 12 is constructed of the same materials as the Nieuport 11 with the exception of the main wing spars which are formed sheet. The 12 is a 2 place with a Rotax 582 recommended. Construction is fabric covered tube structure, pull riveted gussets and AN bolts. Plans are oriented to the experienced builder with little instruction needed. Videos are available of Building procedures 4 hrs as well as a flight preview video (2 hours)

Engine: Rotec R2800 or Rotax 582, 65 hp
HP range: 65-85.
Reduction: 3.47:1
Propeller (flight): 84″ diameter
Span Main Wing: 26.5 ft
Span Sub Wing: 21.2 ft
Chord Main Wing: 4.85 ft
Chord Sub Wing: 31.5
Wing Area: 189 sq. ft.
Span Stabilizer: 9 ft
Length cowl to tail: 21.5 ft
Height: 7.5 ft
Weight empty: 575 bs
Fuel Capacity: 12 Gal US.
Gross Weight: 1070 lbs
Stall Speed: 33 MPH
Cruise: 75 MPH
Top Speed: 94 MPH
Never Exceed (Vne): 112 MPH
Take off run: 300 ft
Landing Roll: 300 ft
ROC: 550 fpm.
Range: 180 sm.
G Factor (@ 550 lbs): +5.7/ – 2.8
Tubes: 6061-T6
Gussets / fittings: 2024 – T3
Build time: 1400 hrs
Seats: 2.
Landing gear: tail wheel.
Engine: Rotax 582, 64 hp
Wing span: 8 m
Wing area: 17.56 sq.m
MAUW: 475 kg
Empty weight: 255 kg
Fuel capacity: 50 lt
Max speed: 150 kph
Cruise speed: 115 kph
Minimum speed: 53 kph
Climb rate: 2.2 m/s
Seats: 2
Plan price (1998): $200
Circa Reproductions Siemens Schukert

A variation of the Graham Lee designed 7/8 scale copy of the 1916 French Nieport 11 is the German copy by Seimens Schukert featuring lowered top wing and four point carbane struts. Rotax 503 powered
Gas powered Spandau MG adds to fun flying.