USA
In May 1970 Cosmic Aircraft Corp acquired all rights in manufacture of F-23 single-seat agricultural monoplane, produced previously by D. D. Funk Aviation Company Inc. Two models: F-23A (Continental radial) and F-23B (Jabobs radial). Production ceased 1975.
Era
Correa 1911 aeroplane

Argentine engineer Federico Correa built this half parasol, half flying-wing machine which was described in 1911. It was powered by a Gnôme engine.
Cornu Helicopter

At Coquainvilliers, near Lisieux, France, Paul Cornu, a bicycle maker, built a practical heli¬copter with fore and aft rotors driven by belts from a 24 hp Antoinette engine, which made a free flight lasting about 20 seconds on 13 November 1907. The machine was stabilized with sticks by men on the ground because of its poor controllability. Powered by an Antoinette engine, it rose about 1 foot on its first flight, and then climbed to 5 feet carrying Cornu and his brother.

The central frame supported the engine, pilot seat and fuel tank, and the whole contraption weighed just over 250kg. To rock the ship from side to side, or to nose up and down, there were movable flat surfaces ‘control vanes’ mounted under the rotors so the airflow would push against them. The system on the Cornu machine was ineffectual.

The chassis rested on a four-wheeled landing gear. The rotors were paddle-shaped and fabric-covered, mounted on large horizontal, bicycle-type wheels situated one at each end of the machine. The design followed that of a small scale model made by Cornu a year or so previously with 2.25m rotors, a 2hp Buchet engine and a weight of 13kg. The full-scale machine made its second flight with Cornu’s brother hanging on to the framework, increasing the total weight to 328kg, and take-offs to about 2m were made later carrying the pilot only.

Cornu was unfortunate in that his flight came just as public hysteria was focusing on the fixed wing achievements of the Wrights. He was unable to obtain support for developing his helicopter.
Engine: Antoinette, 18kW, 24 hp
Rotor diameter: 6m approx
Empty weight: 203kg
Loaded weight: approx 250 kg
Cornu, Paul
The first Paul Cornu helicopter was built in 1906 in Lisieux. The machine weighed 13.75 kg and its Buchet engine delivered a full 2 hp and drove two 2,25 m rotors. Horizontal propulsion was achieved by inclined surfaces that were placed in the downwash from the lifting propellers.


It reached an altitude of three metres and made flights of up to 20 metres.




Cornu Aîné Ballon Remorqueur

The ballon remorqueur, or balloon tug, was a patented dirigible airship conceived and drafted by Cornu Aîné of Nuits, Cote D’Or, France, during the years 1852–1854, with the intention of using compressed steam as its system of propulsion to tow a train of balloon carriages as a proposed aerial express running between Paris and London. The steam reactor system employed a pivoting “point d’appui aerien” (aerial fulcrum) in the shape of a bell set three meters ahead of the nose of the dirigible express. By injecting steam into the bell and deflecting the steam rearward, M. Cornu planned to steer the craft by articulating this hinged fulcrum device.
Cornu Aîné
Cornu Aîné of Nuits, Cote D’Or, France, drafted and patented a dirigible airship conceived during 1852–1854, with the intention of using compressed steam as its system of propulsion.
Cornelius XFG-1

The 677 gal (2,563 l) experimental fuelling glider XFG-1 incorporated Cornelius’ experience with swept-forward wings and was intended to be towed (by a Douglas C 47) pilotless with the controls locked. After the fuel was transferred to the towplane, it was to be cast off and abandoned. An alternative use was as a piloted fuel carrier, jettisoning its undercarriage after take-off, and landing at its destination on two skids at the bottom of the fuselage.
Basically a flying fuel tank, the forward swept wings were mounted behind the cylindrical fuel tank forming the fuselage centre section. The incidence of the XFG-1 wing was adjustable on the ground at 3°, 5° and 7°. With a swept-forward wing, an increase in incidence raises the wingtips and produces dihedral, which may explain why some accounts describe the adjustment as variable-dihedral.
Two were produced for the USAAF in 1945 by the Spartan Aircraft Corporation at Tulsa, Oklahoma, under the serials 44-28059, 44-28060. Thirteen flights were made in prototype 44-28059 by Reitherman, on the last of which he was killed after failing to recover from a spin. The second machine, 44-28060, made 19 flights, but work was discontinued with the end of WW II.
Cornelius Mallard

The Mallard (NX34212) was a forward swept-winged tailless monoplane with a 130 hp Franklin flat-four engine. With side-by-side two-seating it was demonstrated publicly by Alfred Reitherman. No production resulted. The 125 mph cruising speed quoted may have been projected rather than actual, considering it was described as 700 lb overweight and underpowered.
Cornelius LW-1

Continuing to experiment with a wing with a variable angle of attack (variable-incidence wing), American engineer George Wilbur Cornelius built his second aircraft in 1933, the designation LW-1 (from Low-Wing, and as a further development of the PW-1, from Parasol-Wing).
The low-wing two-seater LW-1 (X13706) used the short-lived four-cylinder inverted in-line 120 hp Martin 133 engine and had the same control system as the Cornelius FreWing. The incidence of the mainplanes was adjusted differentially like ailerons, and collectively like elevators in conjunction with a stabilator tailplane.

It was intended to improve performance by dispensing with the drag of the multiple strutting needed for its parasol predecessor.

The LW-1 NX13706 is one of a kind.
Engine: Martin 333, 120 hp
Maximum speed: 237 km/h / 147 mph
Cruise: 201 km/h / 125 mph
Stall: 45 mph
Seats: 2
Cornelius FreWing

The first aircraft of the Cornelius Aircraft Co, the FreWing, was designed by Cornelius and C.C. Spangenberger. It was a parasol monoplane single-seater in which the incidence of the mainplanes was adjusted differentially like ailerons, and collectively like elevators in conjunction with a stabilator tailplane. Initially, each mainplane had a servo surface extending behind it on two booms attached to the undersurface, but these were later removed as unnecessary.
Engine: 125 hp Menasco B-4
Span: 30 ft 6 in (9.30m)
Length: 20 ft 6 in (6.25 m).