The first Gordon England design, the G.E.1, was a two-bay equal-span tractor configuration biplane powered by a 50 hp (37 kW) Clerget four-cylinder water-cooled engine, driving the two-bladed propeller via a chain drive giving a 2:1 speed reduction. The crew of two were accommodated side-by-side in a single cockpit, fitted with dual controls. The empennage consisted of a small triangular tailplane and elevators mounted on top of the rectangular-section fuselage and elongated triangular fins above and below the fuselage with the unbalanced rudder mounted on the trailing edge.
After testing during May and June 1912 the fins were removed, and an enlarged aerodynamically balanced rudder fitted. The aircraft was sold to the Deutsche Bristol Werke. However it was found to be unsuitable for use as a trainer, and was returned to the Bristol works at Filton in September 1912 and scrapped.
The G.E.2 was an enlargement and refinement of the previous design. The fuselage was carried on the innermost pairs of interplane struts, so that there was a gap between the fuselage and the lower wing, and a shallow curved fairing was added to the top and bottom of the fuselage. The tailplane was enlarged and mounted in a mid-fuselage position. Two examples were built, one powered by a 100 hp (75 kW) Gnome double Omega twin-row rotary engine and the other with a 70 hp (53 kW) four-cylinder inline water-cooled Daimler. Both were entered in the British military aeroplane trials held in August 1912, the first to be flown by Gordon England and the other by Howard Pixton but were unsuccessful, completing only the quick-assembly tests. The Daimler-engined version proved underpowered, and the other aircraft was damaged in an accident early in the competition, which was won by the Cody V biplane. Bristol did have some success, however: their monoplane design being placed equal third.
The design was further refined in the G.E.3, of which two were built for the Turkish government. This had a fuselage faired to a circular cross-section with the crew in two tandem cockpits, with fuel and oil tanks sufficient for three hours flight between them, and was powered by an 80 hp (60 kW) Gnome Lambda single-row rotary engine threequarters enclosed in a circular cowling. The continuous inmost interplane struts were replaced by short struts between the lower longerons and the lower wing and a cabane consisting of two sets of inverted V struts supplemented by a single strut between the centre of the upper wing and the nose of the aircraft. Trials of the aircraft revealed that the wing spars were too flexible, and although an attempt was made to address this problem by adding short kingpost-bracing to the rear spar, by this time the Italian blockade of Turkey made delivery difficult, and no further development was carried out.
G.E.1 Engine: 1 x 50hp Clerget Wingspan: 10.26 m / 33 ft 8 in Length: 8.84 m / 29 ft 0 in Wing area: 29.73 sq.m / 320.01 sq ft Max. speed: 105 km/h / 65 mph
G.E.2 Powerplant: 1 × Gnome double Omega, 100 hp (75 kW) Wingspan: 40 ft 0 in (12.20 m) Wing area: 400 sq ft (37.2 sq.m) Length: 31 ft 0 in (9.45 m) Empty weight: 1,080 lb (480 kg) Gross weight: 2,000 lb (907 kg) General characteristics Maximum speed: 68 mph (109 km/h, 59 kn) Crew: two, pilot and observer
The Bristol TB.8 two-seat trainer of 1914-15 was powered by 80 hp rotary engines. Various makes were used including Gnome, Le Rhone and Clerget. Later models were powered by a 100 hp Gnome Monosoupape engine.
RNAS TB.8 – 100 hp Gnome
About 36 were built, of which some were supplied to the RNAS and six went to Roumania.
Wingspan: 37 ft 8 in Length: 29 ft 3 in Max speed: 73 mph
In 1919 Frank Barnwell took the flying surfaces from a Badger – a proposed development of the F2B fighter – and made up a cheap slab-sided fuselage for experimental work. The whole thing cost £250 to build and was known as the Badger X, (and unofficially as Barnwell’s weekender).
It became the first aircraft to appear on the UK civil register as G-EABU on 30 May, by which time Barnwell had turned it over on the golf course adjacent to the Filton airfield. He was left unharmed but angry, hanging from the straps, and he got even angrier when someone released his straps before getting hold of him, and he landed on his head!
In 1911, George Challenger and Archibald Low designed the single seat Bristol Monoplane, powered by a 50 hp Gnôme rotary engine. Two of these machines (No. 35 and No. 36) were built, and exhibited at the Olympia Aero Show in February and in St. Petersburg in March. The monoplane tried at Larkhill, where it was damaged during taxi tests. It was not rebuilt, due to the more promising Bristol-Prier monoplane then under construction.
The Bristol Lucifer was a British three-cylinder, air-cooled, radial engine for aircraft, first run in 1919. Built in the UK in the 1920s by the Bristol Aeroplane Company, it produced 100 horsepower (75 kW).
The Lucifer was originally a Cosmos Engineering engine, Cosmos being taken over by Bristol in 1920.
Applications: Albatros L 69 Avro 504 Boulton Paul P.10 Bristol M.1 Bristol Primary Trainer Handley Page Hamlet NVI F.K.29 Parnall Peto
Lucifer 1 Type: 3-cylinder air-cooled single-row radial engine Bore: 5.75 in (146 mm) Stroke: 6.25 in (159 mm) Displacement: 487 in³ (8.0 L) Diameter: 48 in (1219 mm) Dry weight: 324 lb (147 kg) Valvetrain: Four valves per cylinder, poppet valve Fuel type: Petrol Cooling system: Air-cooled Power output: 100 hp (75 kW) Compression ratio: 4.8:1 Power-to-weight ratio: 0.3 hp/lb
Design work on the Proteus started in September 1944, during the course of development the gas generator section was built as a small turbojet which became known as the Bristol Phoebus. This engine was test flown in May 1946 fitted to the bomb bay of an Avro Lincoln, performance was poor due to airflow problems. The centrifugal compressor was redesigned but similar problems were encountered when the Proteus started ground testing on 25 January 1947.
The original Proteus Mk.600 delivered 3,780 hp (2,820 kW), and was going to be used on the early versions of the Britannia and the Saunders-Roe Princess flying-boat. The versions on the Princess were mounted in a large frame driving a single propeller through a gearbox, and were known as the Coupled Proteus. The Coupled Proteus was also intended to be used on the Mk.II versions of the Bristol Brabazon, but this project was cancelled. Only three Princesses were built, only one of which flew, and by the time the Britannia was ready for testing the manufacturer had decided to equip it with the later Mk.700 Proteus instead.
1949 – 3200 shp Proteus in a Filton test hanger
The Proteus was a two spool, reverse-flow gas turbine, similar to the original Whittle engine designs with an extra turbine stage. Because the turbine stages of the inner spool drove no compressor stages, but only the propeller, this engine is sometimes classified as a free turbine.
May 1957
During development, there were severe problems with compressor blades, turbine blades and bearings failing at even low power output levels. This led to the famous quote of Proteus Chief Engineer Frank Owner to Chief Engineer of the Engine Division Stanley Hooker: “You know, Stanley, when we designed the Proteus I decided we should make the engine with the lowest fuel consumption in the world, regardless of its weight and bulk. So far, we have achieved the weight and bulk!”
At this point the Proteus proved to have troubling icing problems, causing the engine and aircraft projects to be delayed while solutions were found. The Mk.705 of 3,900 hp (2,900 kW) was the first version to see widespread production on the Bristol Britannia 100 and some 300 series. The Mk.755 of 4,120 hp (3,070 kW) was used on the 200 series (not built) and other 300’s, and the Mk.765 of 4,445 hp (3,315 kW) was used on the RAF’s Series 250 aircraft.
Part of the Bristol Proteus flight development was a Lincoln with a Phœbus jet engine in the bomb bay. The Phœbus is a pure jet version of the Proteus and air was drawn in through elephant ears.
Lincoln Phœbus mounting
Variants: As with most gas turbine engines of the 1940s, 50s, and 60s the Ministry of Supply allocated the Proteus a designation which was apparently little used. Officially the Proteus was named Bristol BPr.n Proteus
Proteus series 1 (BPr.1)Prototype and early production engines used for development and testing.
Proteus series 2 Initial production versions, renamed as Proteus 600 series engines.
Proteus series 3 The fully developed initial version, re-named as the Proteus 700 series.
Proteus 600 Initial production engines re-named from Proteus series 2.
Proteus 610 The engines used in the Coupled-Proteus installations for the Saunders-Roe Princess airliner.
Proteus 625
Proteus 700
Proteus 705
Proteus 710 The engines slated for use in the Coupled-Proteus installations of the Bristol Brabazon I Mk.II.
Proteus 750
Proteus 755
Proteus 756
Proteus 757
Proteus 758
Proteus 760
Proteus 761
Proteus 762
Proteus 765
Proteus Mk.255 Military engines similar to the Proteus 765, to power the Bristol 253 Britannia C.Mk.1.
Coupled-Proteus 610 Twin Proteus 600 series engines driving contra-rotating propellers through a combining gearbox, developed specifically for the Saunders-Roe SR.45 Princess. Coupled-Proteus 710 Twin Proteus 710 engines driving contra-rotating propellers for the Bristol Brabazon I Mk.II.
Bluebird Proteus A specially modified Proteus 705 with drive shafts at front and rear of the engine to drive front and rear differential gearboxes on Donald Campbell’s Bluebird-Proteus CN7.
Applications: Bristol Britannia Bristol Type 167 Brabazon I Mk.II Saunders-Roe Princess
Specifications:
Proteus Mk.705 Type: Turboprop Length: 113 in (2,870 mm) Diameter: 39.5 in (1,003 mm) Dry weight: 2,850 lb (1293 kg) Compressor: Two-spool 12-stage axial, followed by a single centrifugal stage Combustors: Reverse-flow Turbine: Two-stage power (free turbine), two-stage driving compressor Fuel type: Aviation kerosene Maximum power output: 3,320 shp (2,475 kW) + 1,200 lb (5.33 kN) residual thrust giving 3,780 eshp Overall pressure ratio: 7.2:1 Fuel consumption: 273 Imp gal (1,241 L) /hour Specific fuel consumption: 0.495 lb/h/eshp Power-to-weight ratio: 1.32 eshp/lb
The Phoenix was an experimental version of the Bristol Aeroplane Company’s Pegasus engine, adapted to run on the diesel cycle. Only a few were built between 1928 and 1932, although samples fitted to a Westland Wapiti held the altitude record for diesel-powered aircraft at 27,453 ft (8,368 m) from 11 May 1934 until World War II. The primary advantage of the Phoenix was better fuel efficiency at cruise, by up to 35%.
Variants: Phoenix I: – Diesel version of the Pegasus IF, 380 hp. Phoenix IIM: – Medium supercharged diesel version of Pegasus IM, 470 hp.
Specifications:
Phoenix I Type: 9-cylinder air-cooled Diesel radial engine Bore: 5.75 in (146 mm) Stroke: 7.5 in (190 mm) Displacement: 1,753 in³ (28.7 l) Length: 43.75 in (1,111 mm) Diameter: 55.25 in (1,403 mm) Dry weight: 1,067 lb (484 kg) Valvetrain: Overhead valve, two intake and two exhaust valves per cylinder, pushrod-actuated. Fuel type: Diesel Cooling system: Air-cooled Power output: 380 hp (283 kW) at 2,000 rpm at sea level Specific power: 0.22 hp/in³ (9.9 kW/L) Compression ratio: 14:1 Power-to-weight ratio: 0.36 hp/lb (0.6 kW/kg)
In late 1925 and early 1926, the RAE published a series of papers by Harry Ricardo on the sleeve valve principle. The main advantages over the traditional poppet valves was better volumetric efficiency, and the ability to operate at higher rotational speeds. This allowed a smaller engine to produce the same power as a larger one, leading to better fuel efficiency and compact design, particularly in multi-row radial engines. Roy Fedden, Bristol’s primary engine designer, became interested in the concept and by 1927 he had constructed a working two-cylinder V as a testbed, with the idea of developing it into a V-12. However several problems cropped up on the design, notably that the sleeves tended to burst during the power stroke and strip their driving gears. This led to a long series of tests and materials changes and upgrades that required six years and an estimated 2 million pounds to cure; however, by 1933 the problems had been worked out, and the Perseus went on to become the first sleeve valve aero-engine in the world to be put into large quantity production.
The result was a Bristol Mercury-sized engine adapted to the sleeve valve system, the Perseus nine-cylinder, single-row, air-cooled radial, and its smaller cousin, the Bristol Aquila. The first production versions of the Perseus were rated at 580 horsepower (433 kW), the same as the same-year model Mercury, which shows that the sleeve system was being underutilised. However this was quickly uprated as improvements were introduced, and by 1936 the Perseus was delivering 810 hp (604 kW), eventually topping out at 930 hp (690 kW) in 1939, while the Perseus 100 with an increased capacity of 1,635 cu in (26.8 L) produced 1,200 hp (890 kW) at 2,700 rpm at 4,250 ft (1,296 m). This far outperformed even the most-developed versions of the Mercury.
The Perseus saw limited use in the civilian field, notably on the Short Empire flying-boats, but was more common in the then-expanding military field where it was found on the Westland Lysander, Vickers Vildebeest, Blackburn Botha, Skua and Roc bombers.
The main contribution of the Perseus is that its mechanicals were used as the basic piston and cylinder for the “twinned” versions, the tremendously successful Hercules and Centaurus. It was in these designs that the advantages of the sleeve valve were finally put to good use, and by war’s end the Centaurus was one of the most powerful engines in the world.
Applications: Blackburn Botha Blackburn Roc Blackburn Skua Bristol Bulldog Bristol Type 148 Cunliffe-Owen Flying Wing de Havilland Flamingo de Havilland Hertfordshire Gloster Goring Hawker Hart Saro A.33 Short Empire Short Scylla Vickers Vellox Vickers Vildebeest Mk.IV Westland Lysander Mk.II
Specifications:
Perseus XII Type: Nine-cylinder single-row supercharged air-cooled radial engine Bore: 5.75 in (146 mm) Stroke: 6.5 in (165 mm) Displacement: 1,520 in³ (24.9 L) Length: 49 in (1,245 mm) Diameter: 55.3 in (1,405 mm) Dry weight: 1,025 lb (465 kg) Valvetrain: Sleeve valve Supercharger: Single-speed centrifugal type supercharger Fuel system: Claudel-Hobson carburettor Fuel type: 87 Octane petrol Cooling system: Air-cooled Reduction gear: 0.5:1 turning a de Havilland variable pitch propeller Power output: 830 hp (619 kW) at 2,650 rpm for takeoff 905 hp (675 kW) at 2,750 rpm at 6,500 ft (1,980 m) Specific power: 0.59 hp/in³ (26.75 kW/l) Compression ratio: 6.75:1 Specific fuel consumption: 0.43 lb/(hp·h) (261 g/(kW·h)) Oil consumption: 0.28 oz/(hp·h) (11 g/(kW·h)) Power-to-weight ratio: 0.88 hp/lb (1.45 kW/kg)
Bristol had originally intended to use the Aquila and Perseus as two of its major product lines in the 1930s, but the rapid increase in size and speed of aircraft in the 1930s demanded much larger engines than either of these. The mechanicals from both of these designs were then put into two-row configurations to develop much larger engines, the Aquila becoming the Taurus, and the Perseus becoming the Hercules.
The Taurus was a 14-cylinder two-row radial sleeve valve design, resulting in an extraordinarily uncluttered exterior and very low mechanical noise. It offered high power with a relatively low weight, starting from 1,015 hp (760 kW) in the earliest versions. It was also compact, with a diameter of 46 inches (1170 mm) which made it attractive to fighter designers. Unfortunately, the engine has also been described as “notoriously troublesome”, with protracted development and a slow growth in rated power. After several years of development, power had been increased from 1,015 hp (760 kW) to only 1,130 hp (840 kW). As the most important applications of this engine were in aircraft that flew at low altitude, engine development efforts focussed on low-altitude performance.
Bristol Taurus 11 14-Cylinder sleeve-valve double bank air-cooled radial engine of 1938 provided 1,065 h.p. at 5,000ft, and was fitted to the Beaufort Mk 1 as well as the Fairey Battle and Fairey Albacore.
The first Taurus engines were delivered just before World War II began and found some use primarily in the Fairey Albacore and Bristol’s own Beaufort torpedo bomber. Starting from April 1940, it was suggested to replace the Taurus engines of the latter by the famous Pratt & Whitney R-1830 Twin Wasp, but this change was postponed to the autumn of 1941 while attempts were made to cure the reliability problems of the Taurus, and later had to be temporarily reversed because of shortages of Twin Wasp engines. The Twin Wasp was, however, strongly preferred, especially for overseas postings, because of its much greater reliability. In later models of the Taurus engine the reliability problems were mostly cured by a change in the cylinder manufacturing process, although the engine kept a poor reputation, and in the Albacore the Taurus engine was retained until the end of that aircraft’s production in 1943.
There were no other operational applications of the Taurus engine, because its initial reliability problems discouraged the development of Taurus-powered aircraft, and because later-war combat aircraft demanded more powerful engines. Its production lines were closed down in favour of the Hercules engine.
Variants
Taurus II 1940 1,060 hp.
Taurus III 935 hp.
Taurus VI 985 hp.
Taurus XII 1940 985 hp. Supercharger ratio decreased, impeller diameter increased.
Taurus XVI 1940 985 hp.
Taurus XX Trials engine only, one built.
Applications Bristol Type 148 Bristol Beaufort Fairey Albacore Fairey Battle testbed only Gloster F.9/37
Specifications
Taurus II Type: 14-cylinder, two-row, supercharged, air-cooled radial engine with dual ignition Bore: 5 in (127 mm) Stroke: 5.625 in (143 mm) Displacement: 1,550 in³ (25.4 L) Length: 49.2 in (1,250 mm) Diameter: 46.25 in (1,175 mm) Dry weight: 1,301 lb (590 kg) Valvetrain: Sleeve valve Supercharger: Single-speed centrifugal type supercharger Fuel system: Claudel-Hobson carburettor Fuel type: 87 Octane petrol Cooling system: Air-cooled Reduction gear: Farman epicyclic gearing, 0.444:1 Power output: 996 hp (743 kW) at 3,225 rpm for takeoff 1,050 hp (783 kW) at 3,225 rpm at 5,000 ft (1,520 m) Specific power: 0.68 hp/in³ (30.83 kW/l) Compression ratio: 7.2:1 Specific fuel consumption: 0.43 lb/(hp·h) (261 g/(kW·h)) Power-to-weight ratio: 0.81 hp/lb (1.33 kW/kg)
Michel Wibault, the French aircraft designer, had the idea to use vectored thrust for vertical take-off aircraft. This thrust came from four centrifugal compressors driven by a Bristol Orion turboprop, the exhaust from each could be directed by rotating the outlets. Gordon Lewis initially planned an engine with two thrust vectors, driven by the compressor, with forward thrust from a conventional rear exhaust in his initial BE.52 design. The BE.52 design was built around a Bristol Siddeley Orpheus which through a shaft drove the first three stages of a Bristol Olympus engine which had inlet and outlets separate of those of the Orpheus. Work was overseen by Bristol Siddeley’s Technical Director Stanley Hooker.
The Bristol Engine Company began work on the BE.53 Pegasus in 1957. While the BE.52 was a self-contained powerplant and lighter compared to Wibault’s concept, the BE.52 was still complicated and heavy. In the BE.53 the Olympus stages were fitted close to the Orpheus stage; this simplified the inlet ducting and the Olympus stages now supercharged the Orpheus improving the compression ratio.
The engine was designed in isolation for a year, then it was helped greatly by understanding what type of aircraft it was designed for. The team received a supportive letter from Sydney Camm of Hawker in May 1957. Hawker were looking for a Hawker Hunter replacement. The aircraft designer, Ralph Hooper, suggested having the four thrust vectors (originally suggested by Lewis), with hot gases from the rear two. Two thrust vectors did not provide enough lift. The 1957 Defence White Paper, which focused on missiles, and not aircraft, also was not good news.
The further development of the engine then proceeded in tandem with the airframe the Hawker P.1127, which first flew in 1960. The next stage of design and development was then flown in the Kestrel, of which nine were built. This was then developed into the Harrier combat aircraft. The engine was partially supported financially from the Mutual Weapons Development Programme.
The flight testing and engine development received no government funding; the plane’s funding came entirely from Hawker. There was only enough thrust in the first engines to barely lift the plane off the ground because of weight growth problems. Flight tests were conducted when the aircraft was tethered. The first free hover was achieved on 19 November 1960. The first, and difficult, transition from static hover to conventional flight was achieved on 8 September 1961. The RAF was not much of a convert to the VTOL idea, and described the whole project as a toy and a crowd pleaser. The first prototype P1127 made a very heavy landing at the Paris Air Show in 1963.
Series Manufacture and Design and Development improvement to ever higher thrusts of the Pegasus was continued by Bristol engines beyond 1966, which was when Rolls-Royce Ltd bought the Company. A related engine design, the 39,500 lbf (with reheat) Bristol Siddeley BS100 for a supersonic VTOL fighter (the Hawker Siddeley P.1154) was not developed to production as the aircraft project was cancelled in 1965.
The Pegasus vectored-thrust turbofan is a two-shaft design featuring three low pressure (LP) and eight high pressure (HP) compressor stages driven by two LP and two HP turbine stages respectively. Unusually the LP and HP spools rotate in opposite directions to greatly reduce the gyroscopic effects which would otherwise hamper low speed handling. The engine employs a simple thrust vectoring system that uses four swiveling nozzles, giving the Harrier thrust both for lift and forward propulsion, allowing for STOVL flight. This unique design highly contributes to the sustainability and success of its carrier, the Hawker Harrier. Many other designs faced flaws as the lift and forward propulsion functions were split using separate engines. In such a concept once the transition from lift to forward or vice versa is completed, any such engine is reduced to dead weight. I.e. in forward flight lift engines do not need to provide thrust anymore, but still need to be carried by the airframe, consuming valuable fuel, increasing weight, decreasing range and occupying costly space that cannot be used for other purposes anymore. Like fuel, avionics or additional ordnance.
The front two nozzles are fed with air from the LP compressor, the rear with hot (650 °C) jet exhaust. The airflow split is about 60/40 front back. It was critical that the nozzles rotate together. This was achieved by using a pair of air motors fed from the HP (high pressure) compressor, in a fail over configuration, pairs of nozzles connected with, surprisingly, motor-cycle chains.
The Pegasus was also the first turbofan engine to have the initial compressor fan, the zero stage, ahead of the front bearing. This eliminated radial struts and the icing hazard they represent.
The engine is mounted in the centre of the Harrier and as such it is necessary to remove the wing to change the powerplant having already sat the fuselage on trestles; the whole change took a minimum of eight hours.
The maximum take-off thrust available from the Pegasus engine is limited, particularly at the higher ambient temperatures, by the turbine blade temperature. As this temperature cannot reliably be measured, the operating limits are determined by jet pipe temperature. To enable the engine speed and hence thrust to be increased for take-off, water is sprayed into the combustion chamber and turbine to keep the blade temperature down to an acceptable level.
Water for the injection system is contained in a tank located between the bifurcated section of the rear (hot) exhaust duct. The tank contains up to 500 lb (227 kg, 50 imperial gallons) of distilled water. Water flow rate for the required turbine temperature reduction is approximately 35gpm (imperial gallons per minute) for a maximum duration of approximately 90 seconds. The quantity of water carried is sufficient for and appropriate to the particular operational role of the aircraft.
Selection of water injection engine ratings (Lift Wet/Short Lift Wet) results in an increase in the engine speed and jet pipe temperature limits beyond the respective dry (non-injected) ratings (Lift Dry/Short Lift Dry). Upon exhausting the available water supply in the tank, the limits are reset to the ‘dry’ levels. A warning light in the cockpit provides advance warning of water depletion to the pilot.
Over 1,347 engines have been produced and two million operating hours have been logged with the Harriers of the Royal Air Force (RAF), Royal Navy, U.S. Marine Corps and the navies of India, Italy, Spain and Thailand.
The unique Pegasus engine powers all versions of the Harrier family of multi-role military aircraft. In US service, the engine is designated F402. Rolls-Royce licensed Pratt & Whitney to build the Pegasus for US built versions. However Pratt & Whitney never completed any engines, with all new build being manufactured by Rolls-Royce in Bristol, England. The Pegasus was also the planned engine for a number of aircraft projects, among which were the prototypes of the German Dornier Do 31 VSTOL military transport project.
Pegasus 2 Otherwise known as the BE53-3, used in the P.1127, 11,500 lbf (51 kN)
Pegasus 3 Used on the P.1127 prototypes, 13,500 lbf (60 kN)
Pegasus 5 Or BS.53-5 (Bristol-Siddeley 53-3). Used for the Hawker Siddeley Kestrel evaluation aircraft. 15,000 lbf (67 kN)
Pegasus 6 (Mark 101) For first Harriers. 19,000 lbf (85 kN), first flown in 1966 and entered service 1969
Pegasus 10 (Mark 102) For updating first Harriers with more power and used for the AV-8A, 20,500 lbf (91 kN), entering service in 1971.
Pegasus 11 (Mark 103) The Pegasus 11 powered the first generation Harriers, the RAF’s Hawker Siddeley Harrier GR.3, the USMC AV-8A and later the Royal Navy’s Sea Harrier. The Pegasus 11 produced 21,000 lbf (93 kN) and entered service in 1974.
Pegasus 14 (Mark 104) Navalised version of the Pegasus 11 for the Sea Harrier, same as the 11 but some engine components and castings made from corrosion-resistant materials.
Pegasus 11-21/Mk.105/Mk.106 The 11-21 was developed for the second generation Harriers, the USMC AV-8B Harrier II and the BAE Harrier IIs. The original model provided an extra 450 lbf (2.0 kN). The RAF Harriers entered service with the 11-21 Mk.105, the AV-8Bs with F402-RR-406. Depending on time constraints and water injection, between 14,450 lbf (64.3 kN) (max. continuous at 91% RPM) and 21,550 lbf (95.9 kN) (15 s wet at 107% RPM) of lift is available at sea level (including splay loss at 90°). The Mk.106 development was produced for the Sea Harrier FA2 upgrade and generates 21,750 lbf (96.7 kN).
Pegasus 11-61/Mk.107 The 11-61 (aka -408) provides 23,800 lbf (106 kN). This equates to up to 15 percent more thrust at high ambient temperatures, allowing upgraded Harriers to return to an aircraft carrier without having to dump any unused weapons which along with the reduced maintenance reduces total cost of engine use. The RAF/RN upgraded its GR7 fleet to GR9 standard, and part of this process is the upgrade of the Mk.105 engines to Mk.107 standard.
Applications: AV-8B Harrier II BAE Sea Harrier BAE Harrier II Dornier Do 31 Hawker Siddeley Harrier Hawker Siddeley P.1127 Intended application – Armstrong Whitworth AW.681
Specifications:
Pegasus 11-61 Type: Twin-spool turbofan Length: 137 in (3.480 m) Diameter: 48 in (1.219 m) Dry weight: 3,960 lb (1,796 kg) Compressor: 3-stage low pressure, 8-stage high pressure axial flow Combustors: Annular Turbine: 2-stage high pressure, 2-stage low pressure Maximum thrust: 23,800 lbf (106 kN) Overall pressure ratio: 16.3:1 Specific fuel consumption: 0.76 lb/lbf-hr Thrust-to-weight ratio: 6:1