Bristol-Siddeley BS.360 / Rolls-Royce RS.360 / Gem

Rolls-Royce Gem

The Rolls-Royce Gem is a turboshaft engine developed specifically for the Westland Lynx helicopter in the 1970s. The design started off at de Havilland (hence the name starting with “G”) and was passed to Bristol Siddeley as the BS.360. When Rolls-Royce bought out the latter in 1966, it became the RS.360.

The Gem is a three-shaft configuration turboshaft/turboprop engine. Basic arrangement is a four-stage axial compressor, driven by a single stage IP (Intermediate Pressure) turbine, supercharging a centrifugal HP (High Pressure) compressor, driven by a single stage HP turbine. Power is delivered to the load via a third shaft, connected to a two-stage free (power) turbine. A reverse flow combustor is featured.

The Gem 42 develops 1,000 shp (750 kW) at Take-off, Sea Level Static, ISA, but the Maximum Contingency Rating (MCR) is 1,120 shp (840 kW).

Applications:
Agusta A129 Mangusta
Westland Lynx

Specifications:

Gem 42
Type: Triple-shaft two-spool turboshaft
Length: 43.4 in (1090 mm)
Diameter: 23.5 in (590 mm)
Dry weight: 414 lb (187 kg)
Compressor: 4-stage axial LP, single-stage centrifugal HP
Turbine: 2-stage power turbine, single-stage LP, single-stage HP
Maximum power output: 1,000 shp (746 kW)
Overall pressure ratio: 12:1

Bristol-Siddeley BS100

The Bristol Siddeley BS.100 was a British twin-spool, vectored thrust, turbofan aero engine that first ran in 1960, the engine was designed and built Bristol Siddeley Engines Limited.
The BS.100 was similar in general arrangement to that of the company’s Pegasus design, but with the addition of plenum chamber burning (PCB), to enable the projected Hawker Siddeley P.1154 VSTOL fighter design to accelerate to supersonic speed. PCB is akin to reheat, but is only applied to the bypass stream (i.e. the front nozzles), as the flow turns from fan exit to the nozzle bearing plane. Variable area front nozzles were required, to maintain consistent fan matching regardless of whether the PCB was alight.
The BS.100 was also intended for the Fokker Republic D-24.
Six had been built when the project was cancelled in early 1965.

BS100
Type: Turbofan
Length:
Diameter:
Dry weight:
Compressor: Two-spool axial flow
Bypass ratio: 0.9:1
Combustors: annular
Maximum thrust:
26,200 lbf (116.54 kN) PCB off
35,900 lbf (159.69 kN) short lift thrust, PCB on
Overall pressure ratio: 11.45:1
Specific fuel consumption:
0.615 lb/(hr·lbf) (62.73 kg/(kN·h)) at 19,200 lbf (85.41 kN) dry thrust
1.16 lb/(hr·lbf) (118.3 kg/(kN·h)) with PCB

Bristol-Siddeley Theseus

The Theseus was the Bristol Aeroplane Company’s first attempt at a gas-turbine engine design, a turboprop that delivered just over 2,000 hp (1,500 kW). A novel feature was the use of a heat exchanger to transfer waste heat from the exhaust to the compressor exit. First run on 18 July 1945, the engine was soon superseded by the Proteus design with more power, and the only extended use of the engine was in two Handley Page Hermes 5 development aircraft.

Following 156 hours of ground runs and the receipt of a test certificate from the Ministry of Supply on 28 January 1947, two Theseus engines were fitted in the outer positions of a four-engined Avro Lincoln for air tests. After ground and taxying test the Lincoln first flew on 17 February 1947.

Applications
Avro Theseus Lincoln
Handley Page Hermes 5

Variants:

Theseus Series TH.11
Variant without heat exchanger

Theseus Series TH.21
Variant with heat exchanger

Specifications:

Theseus Th.21
Type: Mixed compressor turboprop with heat exchanger
Length: 106 in (2,692.4 mm)
Diameter: 49 in (1,244.6 mm)
Dry weight: 2,310 lb (1,047.8 kg)
Compressor: 8-stage axial + 1-stage centrifugal compressors feeding the combustion chambers through a heat exchanger
Combustors: 8 x stainless steel can combustion chambers
Turbine: 2-stage axial + 1-stage axial free turbine driving the propeller
Fuel type: Kerosene (R.D.E. / F / KER)
Oil system: pressure feed to bearings, dry sump, 40 S.U. secs (13 cs) (Intavia 620) grade oil
Maximum power output: 2,800 hp (2,087.96 kW) equivalent at 8,200 rpm at sea level (2,200 hp (1,640.54 kW) + 825 lbf (3.67 kN) residual thrust)
Overall pressure ratio: 3:1
Fuel consumption: 272 imp gal (1,236.5 l) /hr
Specific fuel consumption: 0.5 lb/equiv. hp/hr ( kg/equiv. kW/hr)
Maximum flight rating: 1,500 hp (1,118.55 kW) equivalent at 8,200 rpm at 20,000 ft (6,096 m)

Bristol Titan / Gnome-Rhône 5K Titan

Bristol Titan

The Bristol Titan was a British five-cylinder air-cooled radial engine, designed byRoy Fedden and built by the Bristol Aeroplane Company in the late 1920s. The engine was designed as a five-cylinder radial to use as many parts of the Bristol Jupiter as possible, cylinders, pistons, articulated connecting rods, crankshaft and other minor parts were interchangeable with the Jupiter. It had the same size cylinders as the earlier Bristol Mercury engine, 5.75 in x 6.5 in (844 cu in/13.8 L) and produced between 200-240 hp.

The major significance of the Titan was that it was licensed to Gnome-Rhône and became the pattern for the Gnome-Rhône 5B and 5K. In 1927 Gnome-Rhône was looking for ways out of its license agreement with Bristol for the Jupiter engine of 1920 and began to produce the Gnome-Rhône 5B and 5K without royalties. Later versions of the Bristol Titan also used a Farman style reduction gear produced by Gnome-Rhône.

Gnome-Rhône was not satisfied with simply producing Bristol designs under license, and started a major design effort based around the mechanicals of the Titan engine. The results were introduced in 1927 as the K-series, spanning the 260 hp (190 kW) Gnome-Rhône 5K Titan, the 7-cylinder 370 hp (270 kW) the Gnome-Rhône 7K Titan Major, and the 9-cylinder 550 hp (405 kW) Gnome-Rhône 9K Mistral. With the introduction of the K-series, Gnome-Rhône finally ended royalty payments to Bristol, the Gnome-Rhône 5K was built in much greater numbers than the original Bristol Titan. By 1930 they had delivered 6,000 Jupiters, Mistrals and Titans, making them the largest engine company in France.

Variants:

Titan I
(1928) – 205 hp.

Titan IIF
Modified valve gear.

Titan IV or Titan II (Special)
(1928) – 205 hp, 0.5:1 reduction gear from Bristol Jupiter.

Gnome-Rhône 5K Titan
licence-built Titan II, 230 hp

Gnome-Rhône 7K Titan major
enlarged 7-cyl Titan with many detail improvements, produced by Gnome-Rhône without licence.

Applications:
Avro 504N
Bristol Primary Trainer
Bristol Type 110A

Specifications:

Titan I
Type: Five cylinder air-cooled radial engine.
Bore: 5.75 in (146 mm)
Stroke: 6.5 in (165 mm)
Displacement: 844 in³ (13.8 L)
Diameter: 48.4 in (1229.3 mm)
Dry weight: 500 lb (227 kg)
Valvetrain: Overhead valve, 4 valves per cylinder
Cooling system: Air-cooled
Reduction gear: None, direct drive, left hand tractor
Power output: 210 hp (157 kW) at 1,800 rpm
Specific power: 0.25 hp/in³ (11.4 kW/L)
Compression ratio: 5:1
Power-to-weight ratio: 0.42 hp/lb (0.7 kW/kg)

Bristol Orion

The Bristol Orion aero engine was a two-shaft turboprop intended for use in later marks of the Bristol Britannia and Canadair CL-44. Although the engine was built and underwent a development program, the BE.25 Orion project was cancelled in 1958 by the British Ministry of Supply. At that time, interest in turboprop powered aircraft was beginning to wane, because of the successful introduction of the Boeing 707 and Douglas DC-8 jetliners into airline service.

A single stage HP turbine drove a five stage all-axial HP compressor, whilst a three stage LP turbine drove both the seven stage LP compressor and the propeller, via a reduction gearbox. Thus the Orion used a shared load LP turbine (like the Rolls-Royce Tyne), whereas its predecessor, the Bristol Proteus, had a free-power turbine. The combustor used separate flame cans.

One novel feature of the Orion was a derate from a thermodynamic rating of 9,000 shp at sea level, to enable a constant 5,150 ehp power level to be maintained all the way up to 15,000 ft altitude.
The Orion project was cancelled in January 1958, at a reported total cost of £ 4.75 million.

Applications:
Bristol Britannia

Specifications:

Orion
Type: Twin-spool turboprop
Length: 112.3 in (2,852 mm)
Diameter: 41 in (1,041 mm)
Dry weight: 3,150 lb (1,429 kg)
Compressor: 7 stage low pressure, 5 stage high pressure
Combustors: Annular combustor with 10 flame tubes
Turbine: Single stage high pressure, 3 stage low pressure
Fuel type: Kerosene
Maximum power output: 5,150 eshp (3,840 kW) (maximum takeoff)
Overall pressure ratio: 10:1
Specific fuel consumption: 0.64 lb/eshp/hr
Thrust-to-weight ratio: 1.63 eshp/lb (2.68 kW/kg)

Bristol Jupiter / Orion / Gnome-Rhône 9 Jupiter / Cosmos Jupiter / Brazil Straker Jupiter I / Siemens-Halske Sh20 / Sh21 / Nakajima Ha-1 Kotobuki / PZL Bristol Jupiter / Weiss – Bristol Jupiter VI / Walter Jupiter

The Jupiter was designed during World War I by Roy Fedden of Cosmos Engineering as the Cosmos Jupiter. During the rapid downscaling of military spending after the war, Cosmos became bankrupt in 1920, and was eventually purchased by the Bristol Aeroplane Company on the strengths of the Jupiter design and the encouragement of the Air Ministry. First run on 29 October 1918 the engine matured into one of the most reliable on the market. It was the first air-cooled engine to pass the Air Ministry full-throttle test, the first to be equipped with automatic boost control, and the first to be fitted to airliners.

The Jupiter was fairly standard nine-cylinder single-row piston radial engine in design, but featured four valves per cylinder, which was uncommon at the time. The cylinders were machined from steel forgings, and the cast cylinder heads were later replaced with aluminium alloy following studies by the RAE. In 1927, a change was made to move to a forged head design due to the rejection rate of the castings. The Jupiter VII introduced a mechanically driven supercharger to the design, and the Jupiter VIII was the first to be fitted with reduction gear.

In 1925, Fedden started designing a replacement for the Jupiter. Using a shorter stroke to increase the rpm, and including a supercharger for added power, resulted in the Bristol Mercury of 1927. Applying the same techniques to the original Jupiter-sized engine in 1927 resulted in the Bristol Pegasus. Neither engine would fully replace the Jupiter for a few years.

A 1926 turbo-supercharged version of the Jupiter known as the Orion suffered development problems and only a small number were produced. Metallurgy problems with this turbo-supercharged engine caused the project to be abandoned after only nine engines had been built.

The Jupiter saw widespread use in licensed versions, with fourteen countries eventually producing the engine. In France, Gnome-Rhone produced a version known as the Gnome-Rhône 9 Jupiter which was used in several local civilian designs, as well as achieving some export success. Siemens-Halske took out a license in Germany and produced several versions of increasing power, eventually resulting in the Bramo 323 Fafnir, which saw use in wartime models.

In Japan, the Jupiter was license-built from 1924 by Nakajima, forming the basis of their own subsequent radial aero-engine design, the Nakajima Ha-1 Kotobuki. It was produced in Poland as the PZL Bristol Jupiter, in Italy as the Alfa Romeo 126-RC35,[6] and in Czechoslovakia by Walter Engines. The most produced version was in the Soviet Union, where their Shvetsov M-22 version powered the famous Polikarpov I-16 which was built in the thousands. Production started in 1918 and ceased in 1930 after more than 7100 were built.

The Jupiter is probably best known for powering the Handley Page HP.42 Hannibal airliners, which flew the London-Paris route in the 1930s. Other civilian uses included the de Havilland Giant Moth and Hercules, the Junkers G 31, and the Dornier Do X flying boat which used twelve engines.
Military uses included the parent company’s Bristol Bulldog, as well as the Gloster Gamecock and Boulton Paul Sidestrand. It was also found in prototypes from Japan to Sweden.

By 1929 the Bristol Jupiter had flown in 262 different aircraft types, it was noted in the French press at that year’s Paris Air Show that the Jupiter and its license-built versions were powering 80% of the aircraft on display.

Variants:

Brazil Straker Jupiter I
(1918) 400 hp. Two built.

Cosmos Jupiter II
(1918) 400 hp. One built.

Bristol Jupiter II
(1923) 400 hp.

Bristol Jupiter III
(1923) 400 hp.

Bristol Jupiter IV
(1926) 430 hp. Variable valve timing, Bristol Triplex carburettor.

Bristol Jupiter V
(1925) 480 hp.

Bristol Jupiter VI
(1927) 520 hp. Produced in both high (6.3:1) and low (5.3:1) compression ratios.

Bristol Jupiter VIA
(1927) 440 hp. Civil version of Jupiter VI.

Bristol Jupiter VIFH
(1932) 440 hp. Equipped with gas starter motor.

Bristol Jupiter VIFL
(1932) 440 hp. Compression ratio 5.15:1.

Bristol Jupiter VIFM
(1932) 440 hp. Compression ratio 5.3:1.

Bristol Jupiter VIFS
(1932) 400 hp. Compression ratio 6.3:1.

Bristol Jupiter VII
(1928) 375 hp. Compression ratio 5.3:1, fully supercharged. Built by Gnome-Rhone as the 9ASB.

Bristol Jupiter VIIF
(1929) 480 hp. Compression ratio 5.3:1. Forged cylinder heads.

Bristol Jupiter VIIF.P
(1930) 480 hp. ‘P’ for pressure feed lubrication to wrist-pins.

Bristol Jupiter VIII
(1929) 440 hp. Jupiter VI but compression ratio increased to 6.3:1.

Bristol Jupiter VIIIF
(1929) 460 hp. Jupiter VIII with forged cylinder heads and lowered compression ratio (5.8:1).

Bristol Jupiter VIIIF.P
(1929) 460 hp. As Jupiter VIII with pressure feed lubrication (TBO at this stage in development was only 150 hours due to multiple failures).

Bristol Jupiter IX
480 hp. Compression ratio 5.3:1.

Bristol Jupiter IXF
550 hp. Compression ratio 5.3:1. Forged cylinder heads.

Bristol Jupiter X
470 hp. Compression ratio 5.3:1.

Bristol Jupiter XF
540 hp. Compression ratio 5.3:1. Forged cylinder heads.

Bristol Jupiter XFA
483 hp. Compression ratio 5.3:1.

Bristol Jupiter XFAM
580 hp.

Bristol Jupiter XFBM
580 hp.

Bristol Jupiter XFS
Fully supercharged.

Bristol Jupiter XI
Compression ratio 5.15:1.

Bristol Jupiter XIF
500 hp. Compression ratio 5.15:1.

Bristol Jupiter XIFA
480 hp. As Jupiter XIF with 0.656:1 reduction ratio

Bristol Jupiter XIF.P
525 hp. As Jupiter XIF with pressure feed lubrication.

Bristol Orion I
(1926) Jupiter III, turbo-supercharged, abandoned programme.

Siemens-Halske Sh20, Sh21 and Sh22
Siemens-Halske took out a license in Germany and produced several versions of increasing power, eventually resulting in the Bramo 323 Fafnir, which saw use in wartime models.

Nakajima Ha-1 Kotobuki
In Japan, the Jupiter was license-built from 1924 by Nakajima.

PZL Bristol Jupiter
Polish production.

Alfa Romeo Jupiter
Italian licence production, 420 hp (310 kW).

Alfa 126 R.C.35
Alfa Romeo developed variant

Walter Jupiter
Licence production in Czechoslovakia by Walter Engines

Weiss – Bristol Jupiter VI

Applications:

Cosmos Jupiter:
Bristol Badger
Bristol Bullet
Sopwith Schneider
Westland Limousine

Bristol Jupiter:
Aero A.32
Airco DH.9
Arado Ar 64
Avia BH-25
Bernard 190
Blériot-SPAD 51
Blériot-SPAD S.56
Boulton & Paul Bugle
Boulton Paul P.32
Boulton Paul Partridge
Boulton Paul Sidestrand
Blackburn Beagle
Blackburn Nile
Blackburn Ripon
Bristol Badger
Bristol Badminton
Bristol Bagshot
Bristol Beaver
Bristol Bloodhound
Bristol Boarhound
Bristol Brandon
Bristol Bulldog
Bristol Bullfinch
Bristol Jupiter Fighter
Bristol Seely
Bristol Type 72
Bristol Type 75
Bristol Type 76
Bristol Type 89
Bristol Type 92
Bristol Type 118
de Havilland Dingo
de Havilland DH.72
de Havilland DH.50
de Havilland Dormouse
de Havilland Hercules
de Havilland Hound
de Havilland Giant Moth
de Havilland Survey
Dornier Do 11
Dornier Do J
Dornier Do X
Fairey IIIF
Fairey Ferret
Fairey Flycatcher
Fairey Hendon
Fokker C.V
Fokker F.VIIA
Fokker F.VIII
Fokker F.IX
Gloster Gambet
Gloster Gamecock
Gloster Gnatsnapper
Gloster Goldfinch
Gloster Goring
Gloster Grebe
Gloster Mars
Gloster Survey
Gourdou-Leseurre LGL.32
Handley Page Clive
Handley Page Hampstead
Handley Page Hare
Handley Page Hinaidi
Handley Page HP.12
Handley Page H.P.42
Hawker Duiker
Hawker Harrier
Hawker Hart
Hawker Hawfinch
Hawker Hedgehog
Hawker Heron
Hawker Woodcock
Junkers F.13
Junkers G 31
Junkers W 34
Parnall Plover
PZL P.7
Saunders Medina
Saunders Severn
Short Calcutta
Short Chamois
Short Gurnard
Short Kent
Short Rangoon
Short Scylla
Short Springbok
Short S.6 Sturgeon
Short Valetta
Supermarine Seagull
Supermarine Solent
Supermarine Southampton
Svenska Aero Jaktfalken
Tupolev I-4
Vickers F.21/26
Vickers F.29/27
Vickers Jockey
Vickers Type 143
Vickers Type 150
Vickers Valiant
Vickers Vellore
Vickers Vellox
Vickers Vespa
Vickers Viastra
Vickers Victoria
Vickers Vildebeest
Vickers Vimy
Vickers Vimy Trainer
Vickers Wibault Scout
Westland Interceptor
Westland Wapiti
Westland Westbury
Westland Witch
Westland-Houston PV.3

Gnome-Rhône Jupiter:
Bernard SIMB AB 12
Blanchard BB-1
Fizir F1M-Jupiter
Latécoère 6

Shvetsov M-22:
Kalinin K-5
Polikarpov I-5
Polikarpov I-15
Polikarpov I-16
Tupolev I-4

Specifications:

Jupiter XFA
Type: Nine-cylinder, naturally aspirated, air-cooled radial engine
Bore: 5.75 in (146 mm)
Stroke: 7.5 in (190 mm)
Displacement: 1,753 in³ (28.7 L)
Diameter: 54.5 in (1,384 mm)
Dry weight: 995 lb (451 kg)
Valvetrain: Overhead poppet valve, four valves per cylinder, two intake and two exhaust
Supercharger: Single speed, single stage
Fuel type: 73-77 Octane petrol
Cooling system: Air-cooled
Power output:
550 hp (414 kW) at 2,200 rpm at 11,000 ft (3,350 m) – maximum power limited to five minutes operation.
525 hp (391 kW) at 2,000 rpm – maximum continuous power at 11,000 ft (3,350 m)
483 hp (360 kW) at 2,000 rpm – takeoff power
Specific power: 0.31 hp/in³ (14.4 kW/L)
Compression ratio: 5.3:1
Power-to-weight ratio: 0.55 hp/lb (0.92 kW/kg)

Bristol Hydra / Double Octagon

It appears the Hydra (also known as the Double Octagon) was built as a “backup” design in case the newer sleeve valve engines being designed by Roy Fedden at the same time proved unworkable. Design of the Hydra was led by Frank Owner, who built an experimental V-4 design to test a new twin overhead cam design, a first for Bristol engines which normally used pushrods and rockers. When the V-4 ran successfully, it seems they used four such engines connected to a common crankcase to produce the Hydra.

The cams were operated by rotating shafts leading from the crankshaft at the back of the engine to the top of each cylinder row. The shaft was directly geared to one of the two camshafts, using another driven shaft to transmit power to the second camshaft on the “other side” of the cylinder heads. The arrangement was somewhat complex, but no more so than a pushrod-based system. A side-effect of the use of the overhead cams was that the cylinders were “in-line”, whereas radials typically rotated the second bank of cylinders in relation to the first in order to expose them more fully to the airflow for cooling.

The Hydra had only two valves per cylinder limiting volumetric efficiency. It is generally difficult to properly arrange pushrods for four valve operation in a multi-row radial engine, some of the rods would have to exit the crankcase between the cylinders where there is little room or spare strength. This difficulty was one of the reasons that led to Fedden’s work on the sleeve valve. This is not so much of a problem on an in-line design, and is one of the reasons in-lines of the era were able to compete in performance terms with the generally much simpler radials. The use of the overhead cams on the Hydra avoided this problem as well.

Only two Hydra’s were built. First run in 1931, one was test flown on the Hawker Harrier, and suffered severe vibration at critical RPMs. In the end, Fedden was able to develop the sleeve valve into a superb series of engines, and the Hydra is almost forgotten.

Hydra
Type: 16 cylinder, twin row, air cooled radial engine.
Bore: 5.0 in (127 mm)
Stroke: 5.0 in (127 mm)
Displacement: 1,570 cu in (25.7 L)
Length: 57 in (1448 mm)
Diameter: 46.5 in (1181 mm)
Dry weight: 1,500 lb (680 kg)
Designer: Roy Fedden
Valvetrain: Double overhead camshaft
Supercharger: Medium supercharged
Fuel type: DTD 134 petrol
Cooling system: Air cooled
Reduction gear: Epicyclic geared, reduction ratio 0.424:1, left hand tractor
Power output: 850 hp at 3,000 rpm
Compression ratio: 6:1
Power-to-weight ratio: 0.56 hp/lb