British Aerial Transport Co. / BAT F.K.24 Baboon

The British Aerial Transport Company Limited F.K.24 Baboon was a two-seat training biplane produced during World War I. Using experience gained designing the Bantam, aircraft designer Frederick Koolhoven (assisted by Robert Noorduyn) designed the two-bay biplane elementary trainer.

The aircraft had a flat-sided fuselage and an uncowled 170 hp (127 kW) ABC Wasp engine simply bolted to the firewall. Maintenance and repair costs have been kept to a minimum through the use of interchangeable upper and lower wing panels, ailerons, elevators and rudders.

Six aircraft were planned but only one was built in July 1918 as a consequence of the end of the First World War and the subsequent sharp reduction in orders for military aircraft.

The Baboon was registered with British Aerial Transport Co. Ltd in May 1919. The only notable act was when it won the Hendon Trophy Race over a 20-mile (32-km) circuit in July 1919 flown by Major Christopher Draper. The Baboon was scrapped at Hendon in 1920.

Powerplant: 1 × ABC Wasp I, 170 hp (130 kW)
Propellers 2-bladed BAT tractor, 5 ft (1.52 m), 7 ft 10 in (2.39 m) diameter
Wingspan: 25 ft (7.6 m)
Wing area: 259 sq ft (24.1 m2)
Length: 22 ft 8 in (6.91 m)
Height: 8 ft 10 in (2.69 m)
Empty weight: 950 lb (431 kg)
Gross weight: 1,350 lb (612 kg)
Fuel capacity: 12 imp gal (54.55 l; 14.41 US gal)
Maximum speed: 90 mph (140 km/h, 78 kn)
Landing speed: 40 mph (64 km/h; 35 kn)
Endurance: 2 hours
Rate of climb: 833.33 ft/min (4.2333 m/s)
Time to altitude: 10,000 ft (3,048.0 m) in 12 minutes
Wing loading: 5.2 lb/sq ft (25 kg/m2)
Power/mass: 0.126 hp/lb (0.206 kW/kg)
Crew: 2
Capacity: 400 lb (181.44 kg) disposable load

British Aerial Transport Co. / BAT FK.23 Bantam I

The first prototype F.K.23 was originally ordered as the fourth of a batch of six development F.K.22s, and while retaining the wooden structure with monocoque fuselage, it embodied extensive redesign. Overall span and wing area were reduced to 6.09m and 14.86sq.m respectively, and the tail surfaces were redesigned. Armament comprised two synchronised 7.7mm Vickers guns and power was provided by a 170hp A.B.C. Wasp I, flight testing being initiated in May 1918. Two further prototypes (originally ordered as the fifth and sixth F.K.22s) were similarly powered, but dimensionally larger, and after further redesign resulting from initial flight trials, a batch of 12 F.K.23 Bantam Is was ordered, the first of these being delivered to the RAE at Farnborough on 26 July 1918. At least nine Bantam Is were completed, one of these being sent to France and evaluated at Villacoublay in the late summer of 1918. One example was sent to the USA for evaluation at Wright Field, but this fighter’s principal shortcoming was the poor reliability of its Wasp I engine.

Engine: 170hp A.B.C. Wasp I
Wingspan: 6.09m
Wing area: 14.86 sq.m

British Aerial Transport Co. / BAT FK.22 Bat / Bantam II

The first design by Frederick (Frits) Koolhoven after joining the British Aerial Transport Company (B.A.T.), the private-venture F.K.22 single-seat fighter flown in September 1917 was of wooden construction with a monocoque fuselage. Powered by a 120hp A.B.C. Mosquito six-cylinder radial engine, it displayed sufficient promise to win an official contract for a batch of six development aircraft. The first and third of these were powered by the 170hp A.B.C. Wasp seven-cylinder radial (F.K.22/1) and the second by a 100hp Gnome Monosoupape nine-cylinder rotary (F.K.22/2), the remaining three eventually being completed as prototypes for the F.K.23. The F.K.22/2, retroactively named Bantam II, was the first to fly, commencing its trials in December 1917 and being delivered to Martlesham for official trials on 19 January 1918. Armament comprised two synchronised 7.7mm Vickers guns, and this prototype, later re-engined with a 110hp Le Rhone 9J nine-cylinder rotary, was eventually assigned to the Central Flying School at Upavon.

F.K22
Engine: 120hp A.B.C. Mosquito six-cylinder radial

F.K.22/1
Engine: 170hp A.B.C. Wasp seven-cylinder radial

F.K.22/2
Engine: 100hp Gnome Monosoupape nine-cylinder rotary
Take-off weight: 571 kg / 1259 lb
Empty weight: 393 kg / 866 lb
Wingspan: 7.52 m / 24 ft 8 in
Length: 6.30 m / 20 ft 8 in
Height: 2.26 m / 7 ft 5 in
Wing area: 21.37 sq.m / 230.02 sq ft
Max. speed: 161 km/h / 100 mph

Belite Aircraft Sealite

Belite Aircraft has developed the single-seat Sealite amphibious floatplane that weighs less than 338 pounds empty and meets FAR 103 requirements for ultralight float-equipped “vehicles,” as the FAA calls them.

The Sealite flew in December 2013, the 110th anniversary of the Wright brothers’ first flight at Kitty Hawk. Belite President James Wiebe made the first flight – “I was pleased with this test flight. It demonstrated the performance and utility possible with a single-place amphibious aircraft. The ground roll was very short, the climb rate was impressive, and the landing manners were easy and benign”.

The first flight was from a grass strip but water tests are planned. The vehicle is an adaptation of the company’s UltraCub model. It made the weight with extensive use of carbon fiber in the floats and wing spars. The wings and floats weigh only 20 pounds each.

Bristol Siddeley Double Spectre / de Havilland Spectre

Spectre Dspe.5

The de Havilland Spectre was a bipropellant engine burning kerosene and hydrogen peroxide, built by de Havilland in the 1950s. The power could be controlled from 10-100% delivering 8,000 lbf (35.7 kN) of thrust at full power. In the SR.53 it used the same fuel tanks as the turbojet engine and if run at full power was expected to consume the full load in about seven minutes.

In 1952 static testing commenced with the Spectre DSpe.l. The aircraft industry had no precedent for an engine which would gain in thrust with altitude and the required maximum thrust was estimated at between 2,000 lbf (8.9 kN) and 15,000 lbf (67 kN) thrust. The design was based on a variable thrust which could be throttled from 8,000 lbf (36 kN) to 2,000 lbf (8.9 kN). Design philosophy was matched to the mixed power concept of an aircraft having both a turbojet and rocket engine for maximum operational flexibility.

Technological innovation embraced the Barske high-speed open-impeller centrifugal pumps, as formerly researched in the Walter organisation, regenerative cooling with pump stages both upstream and downstream, gauze catalyst packs, low-loss internal-flow turbine and the use of straight kerosene fuel. The aircraft tanks were to be pressurised to suppress pump cavitation problems.

It went through rig tests commencing in 1953, bench tests from mid-1954, and testing in two Canberras. From flight approval in Autumn 1956, flight experience again posed altitude starvation problems. Clearance was given for flight in the SR.53 prototype from May 1957.

In October 1957 a contract was announced for a more advanced version of the aircraft as the SR.177 to utilise a revised design Spectre DSpe.5 engine together with a reheated supersonic capability 14,000 lbf (62 kN) thrust Gyron Junior turbojet engine, thus meeting a full mixed power aircraft concept. In conjunction with the new engine, development had been undertaken with two major ancillaries, a peroxide starter for the gas turbine and a peroxide auxiliary power unit. Virtually on the heels of the announcement of the contract came the notorious 1957 Defence White Paper declaring that all future combat would be undertaken by computer controlled missiles, and that manned interceptors were now considered obsolete.

Development flying of the SR.53 continued through 39 flights operating to Mach 1.33, and to altitudes at 55,000 ft (17,000 m), as research and construction proceeded on the SR.177, until its cancellation in 1958.

After merging of interests in 1959, it was manufactured by Bristol Siddeley.

The Spectre project was cancelled in October 1960, at a reported total cost of £ 5.75 million.

Variants included:
Dspe.1
Initial version
Dspe.2
Constant thrust version, simpler design
Dspe.3
Development of Dspe.1 with variable thrust
Dspe.4
Development of Dspe.2
Dspe.5
Further development of Dspe.1
DSpe.D.1 Double Spectre
A doubled version of this engine was used for early flight-testing of Blue Steel nuclear stand off bomb, with two chambers arranged vertically.

The conventional Spectre DSpe.5 had been developed alongside a DSpe.4 RATO variant, the latter for the Avro Vulcan and Handley-Page Victor V bombers, another programme subsequently cancelled after a single trial take-off of a Victor from the de Havilland aerodrome at Hatfield. These two engines were then used in combination to power the development rounds of the Blue Steel missile stand-off bomb, together with the peroxide APU, from its first flight in October 1959.

Bristol Siddeley/SNECMA M45H / Rolls-Royce/SNECMA M45H

The Rolls-Royce/SNECMA M45H was a medium bypass ratio turbofan produced specifically for the twin-engined VFW-Fokker 614 aircraft in the early 1970s. The design was started as a collaborative effort between Bristol Siddeley and SNECMA.

The single-stage fan, together with a five-stage LP compressor, was driven by a three-stage LP turbine, whilst the seven-stage HP compressor was driven by a single-stage, air-cooled, HP turbine. An annular combustor and an unmixed exhaust, with a plug-type primary nozzle, were other design features.
The engine was developed at the time of the Rolls-Royce bankruptcy which resulted in delays in developing the engine.

The M45SD-02 or RB.410 was a derivative of the M45H-01 turbofan, designed to demonstrate ultra-quiet engine technologies, needed for STOL aircraft operating from city centre airports.

A geared, variable pitch, fan replaced the first stage of the low pressure (LP) compressor. A modest fan pressure ratio, consistent with the high bypass ratio, meant a low fan tip speed could be employed. A low hot jet velocity was another major design feature.

In reverse thrust, intake air entered the bypass duct, via a gap in the cold nozzle outer wall, and went through the fan, to be expelled through the intake. A small proportion of the bypass duct air entered the IP compressor, via a special diverter valve, to sustain the gas generator. Reverse thrust was obtained by the fan going through fine (rather than feather) pitch. Engine testing took place in the mid 1970s.

Specifications:

M45H Mk.501
Type: Turbofan
Length: 2,600 mm (102.4in)
Diameter: 909 mm (35.8 in)
Dry weight: 673 kg (1,483 lb)
Compressor: 5-stage intermediate pressure and 7-stage high-pressure axial compressor with a single-stage fan
Bypass ratio: 3:1
Combustors: Annular
Turbine: 3-stage low pressure and single-stage high pressure turbines
Maximum thrust: 7,300 lbf (32.4 kN)
Overall pressure ratio: 16.5:1
Thrust-to-weight ratio: 4.9:1

Bristol-Siddeley Orpheus / Fiat 4023 / 4024

The engine had its genesis in a 1952 request by Folland for an engine in the 5,000 pounds (22 kN) class to power a new trainer and lightweight fighter-bomber they were developing. Stanley Hooker, relatively new to the company after an earlier career at Rolls-Royce, took the project under his wing. He delivered a relatively simple and easy to maintain engine, which was put into use in the Folland Gnat, flying in 1955. Developing a Sea Level Static thrust of 4,520 lbf (20.1 kN), the Orpheus 701 had a 7 stage axial compressor driven by a single stage turbine.

Other users, mostly trainers, soon followed, including the Fuji T-1, Hindustan Marut, HA-300,and the experimental Hunting H.126 and Short SB5. In 1957 NATO ran a competition for a light fighter design, asking for entries in both engine and airframe categories. The Orpheus was the unanimous winner of the engine contest, and was thus selected to power the Fiat G.91R and G.91T using Fiat-built versions of the engine.

Many companies in the 1950s were looking at ways of producing a vertical take off and landing aircraft. Michel Wibault had the idea of using a turboshaft engine to drive four large centrifugal blowers which could be swivelled to vector the thrust. Hooker’s engineers decided on using the Orpheus to drive a single large fan that would supply air to a pair of rotating nozzles, while the exhaust flow from the Orpheus was split into two and would supply another pair of nozzles at the rear of the engine. This experimental system developed into the Pegasus.

Fiat G.91, Folland Gnat, Canadair Sabre – all Bristol Siddeley Orpheus powered

Variants:

BOr.1
First run on 17 December 1954, rated at 3,285 lbf (14.61 kN) by Spring 1955, powered the prototype Folland Gnat.

BOr.2
(Mk.701 / Mk.703)

BOr.3
(Mk.801 / 803 / 805)

BOr.4
(Mk.100)

BOr.12
With a simplified reheat system the BOr.12 was rated at 68,100 lbf (302.92 kN) dry and 8,170 lbf (36.34 kN) with afterburning.

Mk.100
De-rated to improve reliability and fuel consumption and increased engine life, rated at 4,230 lbf (18.82 kN) for the Fiat G.91T and Hawker Siddeley Gnat T Mk.1.

Mk.701
Rated at 4,520 lbf (20.11 kN), the Mk.701 was used in the production Folland Gnat F Mk.1 for Finland and India.

Mk.703
The Mk.703 rated at 4,850 lbf (21.57 kN) powered the Hindustan HF-24 Marut Mk.1.

Mk.801
The Mk.801, rated at 4,520 lbf (20.11 kN), powering G.91s. The Mk.801 was identical to the BOr.2 engine except for accessories.

Mk.803
The Mk.803, with improvements to the compressor, rated at 5,000 lbf (22.24 kN), replaced earlier marks used in G.91s.

Mk.805
The Mk.805, de-rated to 4,000 lbf (17.79 kN), powered the Fuji T-1 trainers of the JASDF and the Hunting H.126 jet-flap research aircraft.

FIAT 4023
Mk.803 engines Licence built by FIAT.

FIAT 4023
Mk.803 engines Licence built by FIAT with added fire detection system.

Applications:
Breguet Taon
Fiat G.91
Folland Gnat
Fuji T-1
HA-300
Hindustan Marut
Hunting H.126
Short SB5

Specification:

Orpheus BOr.3 / Mk.803
Type: Turbojet
Length: 75.45 in (1,916 mm)
Diameter: 32.4 in (823 mm)
Dry weight: 835 lb (379 kg)
Compressor: 7 stage axial compressor
Combustors: Can-annular with 7 flame tubes
Turbine: Single stage turbine
Fuel type: Aviation kerosene
Oil system: Pressure spray and metered feed to gearbox and rear bearing. Oil from the rear bearing is lost overboard to the jet efflux.
Maximum thrust: 5,000 lb (2 kN)
Turbine inlet temperature: 1,184 °F (640 °C) maximum continuous
Specific fuel consumption: 1.08 lb/lb/hr(110.1 kg/kN/hr)
Thrust-to-weight ratio: 5.988 lbf/lb (0.0587 kN/kg)

Bristol-Siddeley Gyron Junior / de Havilland Gyron Junior

The de Havilland Gyron Junior was a military turbojet, and a two-fifths output scaling down of the Gyron, starting as Project Study number 43 in 1954. The first prototype Junior ran in August 1955.

Only a little more widely used than the Gyron, it did at least enter serial production with Bristol for the Blackburn Buccaneer S.1 twin-engined Naval strike aircraft. However it was never a successful engine in service. The Buccaneer S.1 was criticised for being underpowered and the later and more numerous S.2 used the more powerful Rolls-Royce Spey instead.

Twin Gyron Juniors, with afterburners, were also used to power the Bristol 188 Mach 2 supersonic research aircraft. The Rolls-Royce Avon had been considered, but only the Gyron Junior was used in practice. The program was a disappointment, if not a failure, and was terminated early without achieving all of the high-speed high-temperature trials that had been intended. The limitation was the poor fuel consumption of the Gyron Junior and surging from the intakes. This could have been solved with Avons and the successful English Electric Lightning intake design, but the Avro 730 project that the 188 was a research aircraft for had been dropped as a result of the 1957 Defence White Paper which cancelled many manned aircraft designs under development as they were expected to be rendered obsolete by guided missiles. Only Mach 1.95 was achieved for a few minutes, endurance at any speed was so restricted by fuel limits that it was impossible to study the long-term “thermal soaking” of a supersonic airframe, as intended. In total 89 were built.

Variants:
Gyron Junior DGJ.1
(or P.S.43)

Gyron Junior DGJ.2
(Mk.101)
Interim production stage, used on Buccaneer S. Mk.1. Variable inlet and guide vane, annular manifold for flap blowing, 121 in (3.1 m) long overall

Gyron Junior DGJ.10
Exhibited in 1958 at Farnborough, longer than the DJG.1

Gyron Junior DGJ.10R
(or P.S.50)
highly augmentation afterburning version for the Bristol 188, dry thrust 10,000 lb, wet thrust 14,000 lb s.t. (62.3 kN). Added zero stage and two rows of variable stators. Variable nozzle for convergent, parallel and divergent/convergent configuration depending on reheat and aircraft speed. Overall length 191 in (4.9 m)

Gyron Junior DGJ.20

Applications:
Blackburn Buccaneer S.1
40 aircraft built

Bristol 188
Only 2 built

Gloster Javelin
Testing only, 1 production FAW Mk.1 modified

Saunders-Roe SR.177
Intended application, not built

Specifications:

Gyron Junior DGJ.10
Type: Single-spool after-burning turbojet
Length: 102.9 in (2.61 m)
Diameter: 41.1 in (1.04 m)
Dry weight:
Compressor: 7-stage axial flow with Variable Inlet GuideVanes (VIGV)
Combustors: Annular compustion chamber with 13 spill-type burners
Turbine: Two-stage axial flow
Fuel type: Aviation kerosene
Oil system: Pressure spray/splash with scavenging
Maximum thrust: 10,000 lbf (44.48 kN) dry, 14,000 lbf (62.28 kN) wet at sea level, 20,000 lbf (88.96 kN)+ at M2.5+ at 36,000 ft (10,972.8 m)
Overall pressure ratio: (DGJ.1)6.4:1
Turbine inlet temperature: (DGJ.1)1,200 °C (2,190 °F)
Power-to-weight ratio:

Bristol-Siddeley Gnome / General Electric T58 / CT58 / de Havilland Gnome / Rolls-Royce Gnome

Rolls-Royce Gnome

The General Electric T58 is an American turboshaft engine developed for helicopter use. First run in 1955, it remained in production until 1984, by which time some 6,300 units had been built. On July 1, 1959, it became the first turbine engine to gain FAA certification for civil helicopter use.

Development commenced with a 1953 US Navy requirement for a helicopter turboshaft to weigh under 400 lb (180 kg) while delivering 800 hp (600 kW). The engine General Electric eventually built weighed only 250 lb (110 kg) and delivered 1,050 hp (780 kW) and was soon ordered into production. First flight was on a modified Sikorsky HSS-1 in 1957, and civil certification for the CT58-100 variant was obtained two years later.

The main production version of the engine was the T58-GE-10, developing 1,400 hp (1,044 kW). The most powerful version, the T58-GE-16, produces 1,870 hp (1,390 kW).

General Electric T58

The Rolls-Royce Gnome is a single spool turboshaft engine originally developed by the de Havilland Engine Company as a licence-built General Electric T58—a mid-1950s design. The Gnome came to Rolls-Royce after their takeover of Bristol Siddeley in 1966, Bristol having absorbed de Havilland Engines Limited in 1961.

A licence to manufacture the T58 was purchased in 1958. The T58 had begun bench testing in 1955 and by 1958 had already been used in helicopters and de Havilland were able to test their first engines in a Westland Whirlwind and Wasp helicopters in August 1959.

A free-turbine turboshaft, it was used in helicopters such as the Westland Sea King and Westland Whirlwind. The design was sub-licensed to Alfa-Romeo and the IHI Corporation.

There were two series produced: the “H” turboshaft for helicopter use, and the “P” turboprop for fixed-wing aircraft.

A single-stage turbine drives the 10 stage all-axial compressor, whilst a two-stage free power turbine drives the load. The combustor is annular. The Gnome differed from the T-58 in having a British developed fuel control system (Lucas).

Because an all-axial design is employed, the final stage compressor rotor blades are amongst the smallest ever manufactured. Normally, a small engine such as this would feature an axial/centrifugal or even a double centrifugal compressor.

The engine was one of the first developed with an analogue computer, de Havilland’s own, as part of the fuel control system, specifically to control fuel flow during acceleration to prevent engine surge from occurring.

The General Electric T58 remained in production until 1984, by which time some 6,300 units had been built. On July 1, 1959, it became the first turbine engine to gain FAA certification for civil helicopter use.

T58s, have been converted to turbojet by the removal of the power turbines and were used as jet engines on:
Maverick TwinJet 1200
Sipa 200
CozyJet
BerkutJet
VelocityJet
Gross Panther Replica

T58 converted to turbojet by Les Shockley (2003). Named SHOCKWAVE 800+

The SHOCKWAVE 800+weighs just 300 pounds and is capable of producing up to 840 pounds of thrust.

The Carroll Shelby turbine cars entered in the 1968 Indianapolis 500 race were powered by T58s. The cars were found to be using variable inlets to get around the USAC regulations on the maximum allowable inlet size and were disqualified.

Turboshaft engines like the GE T58, Lycoming T53/T55 are also used to power high performance powerboats, such as aport and offshore vee, and catamaran hulls like the Skater “Jet Set” or Mystic Powerboats “My Way”, water jet river racers like Unatural Dissaster and hydroplanes. Some of these boats run in excess of 200 mph, despite them being open cockpit pleasure boats.

Variants:

T58-GE-6
T58-GE-8
T58-GE-10
T58-GE-16
CT58-100
CT58-110

H.1000
(Mk.101) 1,050 shp, first production version for use on later marks of Westland Whirlwind

H.1200
1,250 shp, the Westland Wessex uses two H.1200, as the Coupled Gnome, with a coupled gearbox with a limited power of 1,550 shp at the rotor.

H.1400
1,400 shp for the Westland Sea King HAS.1

H.1400-1
1,535 shp, uprated from the 1400 by increasing the gas-generator speed and using improved blades that can operate at higher temperatures for the Westland Sea King HAS.2.

H.1400-1T
For the Westland Commando HC.4

H.1400-2
1,660 shp for the Westland Sea King HAS.5.

H.1400-3
1,720 shp with new two-stage power turbine.

P.1000
Turboprop version of the H.1000

P.1200
Turboprop version of the H.1200

P.1400-3
Turboprop version of the H.1400-3 rated at 1,700 shp.

Gnome Mk.101

Gnome Mk.110
Handed H.1200 engines for Coupled Gnome units used in Westland Wessex helicopters.

Gnome Mk.111
Handed H.1200 engines for Coupled Gnome units used in Westland Wessex helicopters.

Mk.510
Civilianised Gnome engines.

Mk.610
Civilianised Gnome engines.

Gnome Mk 660
Used in the civilian Westland Wessex 60 helicopter

Coupled Gnome
Twin engines driving through a common gearbox to a single output.

Application: General Electric T58
Aerospatiale SA 321K Super Frelon
Agusta A.101
AgustaBell AB204B
Bell UH-1F/TH-1F
Bell X-22 (YT58)
Boeing Vertol BV-107-II
Boeing CH-46 Sea Knight
Fairchild VZ-5 (YT58)
Kaman SH-2 Seasprite
Piasecki XH-21D Shawnee (Model 71)
Sikorsky SH-3 Sea King
Sikorsky HH-3B/C/E/F
Sikorsky HH-52 Seaguard
Sikorsky S-61L/N
Sikorsky S-62
Sikorsky S-67
Sikorsky S-72

Applications: Rolls Royce Gnome
Agusta A.101
AgustaBell AB204B
Agusta-Bell 205BG
Kawasaki KV-107 (Swedish Navy only)
Saunders-Roe SR.N6 hovercraft
Westland Sea King and Commando
Westland Wessex
Westland Whirlwind

Specifications:

T58-GE-8
Type: Free power turbine turboshaft
Length: 55 in (1,397 mm)
Diameter: 16 in (406 mm)
Dry weight: 285 lb (129 kg) without reduction gearbox, 391 lb (177 kg) with reduction gearbox
Compressor: 10 stage axial-flow compressor with variable inlet guide vanes + variable incidence stators in first three stages
Combustors: Annular combustion chamber with 16 burner nozzles on two manifolds
Turbine: 2x gas generator power turbine stages + 1x free power turbine stage
Fuel type: Aviation kerosene
Maximum power output: 1,250 hp (932.12 kW)
Overall pressure ratio: 8.3:1
Specific fuel consumption: 0.64 lb/hp/hr (0.389 kg/kW/hr) at maximum continuous rating
Power-to-weight ratio: 6.1 hp/lb (10.024 kW/kg) without reduction gearbox

Gnome H1400-1
Type: Turboshaft
Length: 54.8 in (1392 mm)
Diameter: 22.7 in (577 mm)
Dry weight: 334 lb (151.5 kg)
Compressor: Ten-stage axial flow
Combustors: Annular
Turbine: Single-stage compressor turbine, two-stage power turbine
Maximum power output: 1,500 shp (1,119 kW)
Overall pressure ratio: 8.4:1
Power-to-weight ratio: 4.5 shp/lb