
The 1910 Call E-1 /OL-295 was a 45-50hp, 296.31ci two-cylinder, horizontally opposed, water cooled aero engine. The dry weight was 135 lb.

The 1910 Call E-1 /OL-295 was a 45-50hp, 296.31ci two-cylinder, horizontally opposed, water cooled aero engine. The dry weight was 135 lb.

Henry Laurens Call was a writer, a member of the American Association for the Advancement of Science and the designer of this huge, complicated craft, which was powered by two 20hp Curtiss engines, spanned 41 feet and weighed 3,000lbs. It was intended to transport several passengers in the air, on water and on roads, with hot food and all kinds of comfort. However, Call stated that there were too many trees in Girard, Kansas where it was built, and the roads were not very good, so he was never been able to get up a speed of more than 18 miles per hour, rather than the thirty miles an hour he claimed was necessary for the ship to rise in the air.


The 1911 Call 2 monoplane was created by the “Aerial Navigation Company of America” of Henry Laurens Call in 1911. It was powered by a 50 hp, horizontally opposed two-cylinder, four-stroke, Call Aviation Engine.
It made several flights before being destroyed by a tornado.
The Aerial Navigation Company of America, based in Girard, Kansas was founded by Henry Laurens Call.
The company built 14 aircraft, but the Call 2 of 1911 was the only one that was successful.
The Call Aviation Engine, a 50 hp, horizontally opposed two-cylinder, four-stroke, was heavily advertised in the aviation press at that time.

The CM-44 was designed and built by Scaled Composites for California Microwave (CMI). The aircraft was a canard pusher which carried 700 lbs of electronic gear for surveillance. It was test flown by Michael Melvill in April 1987 and found to have a several winglet induced yaw problem that Scaled could not fix. Hollmann contacted CMI and promised to fix it. Dr. Ilan Kroo from Stanford, set up a lattice element model of the CM-44 and fixed the problem and improved the design. Hollmann at ADI designed new wings, winglets and canard for the CM-44. High Tech Composites built the molds and parts. It was test flown by CMI and found to be significantly better than the original design.
First flown April 1930 Model A built for a new Cairns-designed engine

Georges Cailler, born in Vevey, Switzerland as the eldest son of Alexandre Cailler, founder of the well-known chocolate factory in Broc. He built four aeroplanes and flew them between Broc and Epagny. The parts of flying machines of Cailler were built by workers of the the chocolate factory. At the age of 18, he began construction of a biplane with the help of his friend Henri Magnenat from Lausanne, but their machine did not bring expected satisfaction. The trials with the new monoplane took eight days in spring 1910. The boys flew several hundred meters to a height of about 8 meters. They are believed to be the first Swiss aviators to fly a monoplane built entirely in Switzerland by Swiss. The machine is often attributed to Cailler alone.

CAG Toxo is available with bigger engines in VLA version.
Toxo ultralight
Stall: 35 kt / 40 mph / 64 kmh
Cruise: 119 kt / 137 mph / 220 kmh
VNE: 189 kt / 217 mph / 350 kmh
Empty Weight: 284 kg / 626 lbs
MTOW Weight: 450 kg / 992 lbs
Climb Ratio: 1400 ft/min / 7,5 m/s
Glide Ratio: 16
Take-off distance (50ft obstacle): 160 ft / 49 m
Landing distance (50ft obstacle): 250 ft / 76 m

Tom Cadet designed and built the Mk1 Boorabee in 1992. The Mk1 Boorabees flew with a Rotax 503and the first aircraft has had at least 3 different engines including an HKS fitted in 2010.
The original fuselage pod mould for the Boorabee was made from the two halves taken from a crashed Rotec Panther, then modified by making the front more pointed and taking the aft section up to the wing. Tom also added a sheet alloy floor pan. A Maxair Drifter contributed the aluminium tube boom and empennage.
Dave Donohoe, a colleague of Tom Cadet, developed the Boorabee’s airfoil. This wing was mated to a new fuselage mould to use a 4 x 3 inch rectangular boom and Dave called the result the Shuttle.
For the Boorabee’s wing, Tom used fibreglass/Kevlar ribs with a glass/Kevlar leading edge. The main spar caps are 40 x 1.6mm drawn alloy tubes with 1.2mm sheet web plates; the rear spar is a 44 x 1.6mm tube.
Boorabees are extremely docile aircraft with few if any vices. The Mk1s are really powered gliders without air brakes (better than 12:1 glide) they tend to float so it requires a special technique to spot land them.
Cadet built two Mk1 Boorabees then made new moulds and simplified the design for the Mk2.
Three versions of the Boorabee appeared. The Mk 1 has a 30ft wing span. That of the Mk 2 was reduced to 29ft, and a new mould was made to improve the shape of the fuselage pod. Alloy shear plates were used to simplify wing construction, and flaperons adopted. Kevlar was used extensively to lighten the aircraft. Both the first Mk 1 and Mk 2 were registered in 1993.

A lengthened pod, offering more foot space for the rear-seat passenger, was introduced with the Mk 3, which also had the shorter wing.
The choice of powerplant was usually the Rotax 582 or 618. A Rotax 503 was used by Bob Evans of Evans Head for his Mk 2, completed as a single seater with a more rounded tail.
There were nine Boorabees built in total before Cadet gave the fuselage plug to Dave Donohoe who modified it for a rectangular boom tube. Dave’s Shuttle shared the same wing but the boom, tail, undercarriage and controls were vastly different. Cadet loaned the moulds to persons he trusted, and gave them the CAD plans at no cost.
For several years, Tom freely provided scale drawings to those interested in building a Boorabee, the use of his moulds, and builder support. A dozen or so Boorabees were completed by local builders.

As with all pusher aircraft, the airflow around the rear of the fuselage was a problem, causing slight instability in yaw as well as reduced thrust from the propeller. After experiments on the Mk 1s a line of vortex generators on the fuselage immediately solved the issues. Because the two blades of the original propeller disturbed the air at the wing trailing edge in unison, resulting in uncomfortable vibration at certain speeds, a three-blade propeller was found to be necessary. Apart from these annoyances the Boorabee proved very successful, with hundreds of hours logged by each aircraft.
No more Boorabees were built because it required a great deal of effort by Cadet for builder assistance and it became very difficult to get the 5″ boom tube and necessary drawn tubing to build the wing. He still had the moulds years later.
The first Boorabee has flown thousands of hours.
Boorabee Mk1
Engine: HKS 700 E 60hp
Wingspan: 9.2 m / 30 ft
Length: 5.85 m
Empty Weight: 284 kg
Maximum Take Off Weight: 554 kg
Fuel Capacity: 94 litres
Never exceed: 90 Kts
Cruise Speed: 60Kts
Stall Speed: 30 Kts
Take off roll: 200 meters
Rate of Climb: 500 ft per minute
Endurance: 10 hours
Seats: 1
Mk 2
Wing span: 29 ft
Mk 3
Wing span: 29 ft

The 1910 BIS No. 2 biplane was designed and built by Bylinkin, Iordan and Sikorsky in Russia.
Span: 26’3″
Length: 26’3″
Weight loaded: 473 lb