CTA Heliconair HC-I Convertiplano

The Heliconair HC-Ib Convertiplano sits nearly finished in a hangar. The slit behind the cockpit was the intake for air used to cool the fuselage-mounted R-3350 engine. The scoop on the upper fuselage brought air to the engine’s carburetor. Note the Spitfire wings and main gear.

Immediately following World War II, Germany was prohibited from designing and manufacturing aircraft. Post war, Henrich Focke assisted with helicopter development in France and worked for a car company in Germany. He also spent some time in the Netherlands, where he began to design a VTOL aircraft that was capable of relatively high speeds. In 1952, Focke was recruited by the CTA (Centro Técnico de Aeronáutica or Technical Center of Aeronautics) to work in the recently established ITA (Instituto Técnico de Aeronáutica or Technical Institute of Aeronautics). The ITA was the first of four institutes formed by the CTA, all of which were located in São José dos Campos, Brazil. Brazil was working on building an aeronautics and aerospace industry and was actively recruiting German engineers. In addition to Focke, many of his associates and former co-workers were also recruited.

The CTA was impressed with Focke’s VTOL aircraft design and approved its construction. The CTA believed that the aircraft’s capabilities would allow it to reach remote parts of Brazil. Focke set to work on the aircraft—a tiltrotor convertiplane design that was partially inspired by the Fa 269. The aircraft was known as the Heliconair HC-I Convertiplano. Its fuselage and wings were fairly conventional for an aircraft, but it had of two sets of rotors. One pair of rotors was placed near the nose of the aircraft, and the other pair was placed between the wings and tail. All of the rotors were of a tractor configuration and rotated up for vertical flight. The HC-I accommodated two pilots in the cockpit and four passengers in the fuselage. The aircraft’s estimated performance included a top speed of 311 mph (500 km/h) and a range of 943 miles (1,517 km).

The test rig for the engine, transmission, gearboxes, shafts, right-angle drives, and rotors illustrates the complexity of the HC-Ib’s power system. The R-3350 engine did not have any Power Recovery Turbines, which means it was not a Turbo Compound engine.

To save time and money, the decision was made to build the HC-I using the wings and the horizontal stabilizer from a Supermarine Spitfire. A Spitfire XIVe (RM874) was purchased without its Rolls-Royce Griffon 65 engine from Britain by the Brazilian Air Attaché on 19 December 1952. A new fuselage was built to house a 3,000 hp (2,237 kW) Armstrong Siddeley Double Mamba turboprop engine behind the passenger compartment. However, Armstrong Siddeley and the British did not want one of their new, advanced engines being used in such a radical project and declined selling a Double Mamba engine to Brazil.

Focke and the Convertiplano team changed the HC-I’s design to accommodate a 2,200 hp (1,641 kW) Wright R-3350 radial engine and redesignated the aircraft HC-Ib. The R-3350 was larger and heavier than the Double Mamba, and it produced less power. Some sources state a Turbo Compound R-3350-DA3 (3,250 hp / 2,424 kW) was used, but images show that there are no Power Recovery Turbines on the engine installed in a test rig. Extensive modifications to the aircraft’s fuselage were required to accommodate the air-cooled engine. The passenger compartment was omitted, and the R-3350 was installed in the middle of the fuselage. An annular slit behind the cockpit was added to bring in cooling air for the engine. After passing through the engine’s cylinders, the air exited via a jet-like duct at the rear of the aircraft. The Spitfire’s landing gear was strengthened to compensate for the R-3350’s weight.

The HC-Ib sits in the background with the front and rear gearboxes and rotor drives in the foreground. The rotor blades, the only surviving component of the Convertiplano project, are not seen in the image. Note the opening at the rear of the fuselage, which was the exit for engine cooling air.

A gearbox transmission mounted to the front of the R-3350 split the engine’s power to two shafts. The front shaft extended from the engine to the front gearbox. The front gearbox had shafts that extended to the left and right. These shafts led to right-angle gearboxes that powered the front rotors. Power delivery for the rear rotors was more complex. A shaft extended vertically from the transmission on the front of the engine and met a right-angle gearbox positioned directly above the engine. From the right-angle gearbox, a shaft extended back to the rear gearbox. The rear gearbox had the same shafts and right-angle drives for the rear rotors as the front gearbox. The transmission and gearboxes were designed by Willi Bussmann and built by BMW in Germany. Bussmann was a former BMW employee and had worked with Focke on several Focke-Achgelis projects.

Each rotor consisted of three blades. The blades were built in Sweden and made of a steel frame that was covered with wood. The blades’ pitch automatically adjusted and had collective and cyclic control. The rotors were counter-rotating, with the right rotors turning counterclockwise and the left rotors turning clockwise. The HC-Ib had a 37 ft 6 in (11.42 m) wingspan and was 35 ft 3 in (10.74 m) long.

Given the state of the aircraft and the surrounding unchecked growth of vegetation, it can be assumed this image is of the R-3350 engine being removed sometime after the HC-Ib project was cancelled. The image does give proof that the engine was installed in the airframe at one point.

A rig was built, and tests of the engine, gearboxes, shafts, right-angle drives, and rotors began in late 1953. However, vibrations from the radial engine caused some issues that took time to resolve. The HC-Ib airframe was almost completely constructed and had its engine installed when the project was cancelled in 1955. The aircraft was more expensive than anticipated, and interest in the HC-1b had steadily declined after the switch to the R-3350 engine. To make matters worse, many of the Germans returned to Europe or went to the United States as their contracts with the CTA expired. Some Germans did stay and ultimately became part of Embraer. After the project was cancelled, the HC-Ib Convertiplano was left to rot in outside storage for some time and was eventually scrapped in the 1970s. There are some reports that the rotor blades are the only part of the aircraft that survived.

Celier Aviation XeWing

The Celier XeWing (contraction of Xenon Wing) is a Polish ultralight aircraft that was designed by Frenchman Raphael Celier and produced by his company Celier Aviation of Jaktorów-Kolonia, Poland.

The XeWing was developed by mating the fuselage from the Celier Xenon 2 gyroplane with a newly designed folding strut-braced parasol wing in place of the rotor system. The aircraft was intended to comply with the Fédération Aéronautique Internationale microlight rules. It features a two-seats-in-side-by-side configuration enclosed cockpit, fixed tricycle landing gear and a single engine in pusher configuration.

The aircraft wing is made from aluminum sheet, has a span of 6.6 m (21.7 ft) and an area of 10 m2 (110 sq ft). The wing can be folded for ground transportation and storage. The standard engine specified was the 100 hp (75 kW) Rotax 912ULS four-stroke powerplant.

Despite the commonality of the fuselage and engine package with the Xenon 2, the XeWing cannot swap its fixed wing for a rotor system.

It was introduced at AERO Friedrichshafen in 2009. The aircraft was intended to be supplied as a kit for amateur construction or as a complete ready-to-fly-aircraft (projected price of €60,000, assembled, in 2011).

By 2012 the company was no longer advertising the XeWing and it is unlikely that it progressed beyond the prototype stage.

XeWing
Engine: 1 × Rotax 912ULS, 75 kW (101 hp)
Wingspan: 6.6 m (21 ft 8 in)
Wing area: 10 m2 (110 sq ft)
Empty weight: 300 kg (661 lb)
Gross weight: 472.5 kg (1,042 lb)
Fuel capacity: 85 litres (19 imp gal; 22 US gal)
Cruise speed: 150 km/h (93 mph, 81 kn)
Stall speed: 70 km/h (43 mph, 38 kn)
Crew: one
Capacity: one passenger

Celier Aviation Kiss

The Celier Kiss is a series of Polish autogyros that was designed by Frenchman Raphael Celier and produced by his company, Celier Aviation of Jaktorów-Kolonia, Poland. When it was available the aircraft was supplied as a kit for amateur construction or as a complete ready-to-fly-aircraft.

The tandem seat Kiss series was designed as a complement to the side-by-side configuration Celier Xenon 2 series of autogyros. The Kiss series all feature a single main rotor, tricycle landing gear, a low-set T-tail and a choice of engines, all mounted in pusher configuration.

In 2011 the Kiss 912, assembled, cost €29,900.

Variants:

Kiss 912
Base model, with two seats in tandem, powered by a 80 hp (60 kW) Rotax 912UL engine in pusher configuration. The cockpit has a semi-enclosed fairing with a windshield.
Main rotor diameter: 8.4 m (27 ft 7 in)
Main rotor area: 55.4 m2 (596 sq ft)
Empty weight: 200 kg (441 lb)
Gross weight: 450 kg (992 lb)
Fuel capacity: 50 litres (11 imp gal; 13 US gal)
Maximum speed: 140 km/h (87 mph, 76 kn)
Endurance: 3 hours
Rate of climb: 3 m/s (590 ft/min)
Disk loading: 8.1 kg/m2 (1.7 lb/sq ft)
Crew: one
Capacity: one passenger

Kiss 912S
Upgraded model, with two seats in tandem, powered by a 100 hp (75 kW) Rotax 912ULS engine in pusher configuration. The cockpit has a fully enclosed fairing.

Kiss 914
Turbocharged model, with two seats in tandem, powered by a 115 hp (86 kW) Rotax 914 engine in pusher configuration. The cockpit has a fully enclosed fairing.

CEI Free Spirit Mk. II

Originally developed by Cabrinha as the Free Spirit Mk I and first flown 1986.
A composite design with forward swept wing and 2+1 seating. First flown in 1995. The kit price in 1998 was US$24,950.

Engine: Continental IO-360, 210 hp.
Speed max: 265 mph.
Cruise: 220 mph.
Range: 1400 sm.
Stall: 52 mph.
ROC: 2000 fpm.
Take-off dist: 600 ft.
Landing dist: 750 ft.
Service ceiling: 24,000 ft.
Fuel cap: 52 USG.
Weight empty: 1150 lbs.
Gross: 2150 lbs.
Height: 7.5 ft.
Length: 20.6 ft.
Wing span: 30.3 ft.
Wing area: 85 sq.ft.
Seats: 3.
Landing gear: retractable nose wheel.