Nostalgair N3 Pup / Super Pup / Ultra Pup / Stinger / Super Pup

Ultra Pup

Bob Counts developed the single-seat N-3 Pup in the mid-’80s as what might be termed the third generation of ultralights. The Pup was among the first ultralights to resemble a general aviation aircraft, the Piper J-3 Cub in this case. Like several innovative ultralights, the N-3 Pup won a Best New Design award at its first Sun ’n Fun appearance.

The original N-3 Pup being a ¾ scale Super Cub replica. Centre mounted joy stick, rudder pedals, tailwheel steerable through rudder pedals. The N3 Pup has a welded chromemoly steel fuselage and a two-cylinder horizontally-opposed Global engine to add to its air of authenticity. By 1995 marketed as the Preceptor Aircraft Corp Pup from 1230 Shepard St, Hendersonville, NC 28792, USA.

The N-3 Pup can be ordered with folding wings. In less than ten minutes you can fold your wings and take your pup home with you, or unfold them and go flying. The N-3 Pup is a real joy to fly with easy, docile handling. The N-3 Pup built as a bare minimum plane will meet the FAR 103 requirement.

The N-3 Pup was followed by Counts’ larger, souped up version of the N-3, the Super Pup. Empty weight (450 pounds) and flight speeds take it out of the ultralight category. The Super Pup has folding wings, short takeoff and landings and a reliable 4 stroke engine. Wing sub-kits come with ailerons, all hardware, brackets, fittings, fuel tanks, ribs, skins, spars and lift struts. No fabric.

Fuselage sub-kits come with stabilizers, elevators, rudder, landing gear, seat cusions, control systems, all glass, blank instrument panel, wheels and brakes, tailwheel, stringer formers, shock struts, brackets, fittings, firewall and all hardware and necessary accessories. No fabric.

Firewall forward package comes with engine, exhaust stacks, intake manifolds, carb heat, engine mount, prop, carburetor and hardware Engine prices will vary depending on model, Horsepower and electrical option.

The two place Ultra Pup features folding wings, roomier cabin, and electric starting, which all called for a redesigned fuselage. The CG was shifted to accommodate the extra weight up front. Instead of adding weight in the tail, they used heaver-gauge tubing at strategic locations. Thus, we achieved the desired CG shift by adding strength, not just dead weight. Building smarter safer aircraft for all to enjoy has always been the “Preceptor Way”.

Wing sub-kits come with ailerons, all hardware, brackets, fittings, fuel tanks, ribs, skins, spars and lift struts. No fabric.

Fuselage sub-kits come with stabilizers, elevators, rudder, landing gear, seats cusions, control systems, all glass, blank instrument panel, wheels and brakes, tailwheel, stringer formers, shock struts, brackets, fittings, firewall, all hardware and necessary accessories. No fabric.
Firewall forward package comes with engine, exhaust stacks, intake manifolds, carb heat, engine mount, prop, carburetor and hardware. Engine prices will vary depending on model, Horsepower and electrical option.

Stinger

The LSA Stinger uses the same fuselage as the N-3 with front fuselage wider, cabin structure deleted and combing added. The (1995) US$6700.00 kitset came complete with paint and ready to assemble. Skis and floats are optional. Preceptor has taken the same fuselage as used on the time proven N-3 Pup, made the front of the fuselage wider, left off the cabin structure, added a combing and have come up with one of the cutest and nicest flying little open cockpit parasols going. The Stinger brings back the joy of owning and flying an open cockpit airplane that has performance that will keep you smiling. A real beauty that looks and feels like an antique racer of the good old days.

Initially produced by Nostalgair, N-3 kits were subsequently made by Mosler Motors, which eventually sold kit production rights back to Counts. A company named TEC took over engine production from Mosler, but it quit making engines in 1991. At that point, Preceptor began assembling VW-based engines of various strengths. The 70-hp version remains the recommended engine for the Super Pup. Wing and fuselage kits may be bought separately, but one can save $1400 if they’re purchased together. A firewall-forward package for $7600 is for the 70-hp Preceptor VW-based engine that claims a 1400-fpm climb rate. Bob Counts’ son Duwayne runs Preceptor Aircraft by 1995, marketing the Cubs.

June 1997

N-3 Pup
Engine: Global (920cc) 25hp
Empty wt: 248 lbs
Wing span: 30’
Wing area: 123 sq.ft
Height: 5’
Length: 16’6”
Fuel cap: 5 USG
Construction: Aluminium, Wood, Steel
Max wt: 535 lbs
Stall speed: 27 mph
Max speed: 63 mph
Vne: 95 mph
Climb rate: 600 fpm @ 45 mph
Design limit: +6, -3g
Glide ratio: 12-1
Wing loading: 4.35 lbs/sq.ft
Power loading: 21.4 lbs/hp.

N-3 Pup
Engine: TEC, 40 hp
Speed max: 63 mph
Cruise: 60 mph
Range: 150 sm
Stall: 27 mph
ROC: 500 fpm
Take-off dist: 150 ft
Landing dist: 150 ft
Service ceiling: 10,000 ft
HP range: 40-75
Fuel cap: 5 USG
Weight empty: 250 lbs
Gross: 650 lbs
Height: 5 ft
Length: 16.5 ft
Wing span: 30.5 ft
Wing area: 120 sq.ft
Seats: 1
Landing gear: tail wheel

N3 Pup
Engine: 1037 cc Hummel Half VW, 37 HP
Horsepower: 37-50
Propeller: 54 x 22
Overall Length: 16 ft 6 in
Height: 5 ft
Wingspan: 30 ft 6 in
Wing Area: 120 sq.ft
Wing Loading: 3.76 lb.sq.ft
Empty Weight: 254 lb
Gross Weight: 535 lb
Useful Load: 281 lb
Fuel Capacity: 5 USGallons
Best Speed: 63 mph
Cruise Speed: 60 mph
Stall Speed @ Gross w/Full Flaps: 27 mph
Service Ceiling: 10,000 ft
Takeoff Distance: 150 ft
Landing Distance: 150 ft
Rate of Climb (gross): 600 fpm
Fuel burn: 1.8 USgph
Ultimate “G” Loading: +10.0 – 3.0
Cabin Width: 22.75 in
Seats: 1
Landing Gear: FG (Tailwheel)
Complete Kit Cost (2009): US$ 11,700
Less engine, instruments, fabric, prop

Stinger
Engine: TEC 4 stroke, 50 hp
HP range: 35-60
Speed max: 90 mph
Cruise: 80 mph
Stall: 27 mph
Take-off dist: 100 ft
Landing dist: 150 ft
Fuel cap: 10 USG
Weight empty: 350 lbs
Gross: 650 lbs
Height: 5 ft
Length: 17 ft
Wing span: 30.5 ft
Wing area: 122 sq.ft
Seats: 1
Landing gear: tail wheel
Cockpit width: 22.75 in

Stinger
Engine: 1600 cc VW, 50 HP
Propeller: 58 x 28
Overall Length: 17 ft 3 in
Height: 5 ft 6 in
Wingspan: 30 ft 6 in
Wing Area: 120 sq.ft
Wing Loading: 4 lb/sq.ft
Empty Weight: 400 lb
Gross Weight: 660 lb
Useful Load: 260 lb
Fuel Capacity: 10 USGallons (Option for 14 USGallons)
Best Speed: 90 mph
Cruise Speed: 80 mph
Stall Speed @ Gross w/Full Flaps: 35 mph
Service Ceiling: 10,000 ft
Takeoff Distance: 300 ft
Landing Distance: 300 ft
Rate of Climb (gross): 1000 fpm
Fuel burn: 3.5 USGallons Per Hour
Cabin Width: 22.75 in
Ultimate “G” Loading: +5.0 – 3.0
Landing Gear: FG (Tailwheel)
Seats: 1

Super Pup
Engine: VW, 50 hp
HP range: 50-75
Speed max: 115 mph
Cruise: 95 mph
Range: 300 sm
Stall: 35 mph
ROC: 1500 fpm
Take-off dist: 150 ft
Landing dist: 150 ft
Service ceiling: 12,000 ft
Fuel cap: 12 USG
Weight empty: 350 lbs
Gross: 1000 lbs
Height: 5.5 ft
Length: 17.25 ft
Wing span: 30.5 ft
Wing area: 122 sq.ft
Seats: 1
Landing gear: tail wheel

Super Pup
Engine: 2180 cc VW Conversion 70 HP
Horsepower: 50 – 80
Propeller: 62 x 28
Overall Length: 17 ft 3 in
Height: 5 ft 6 in
Wingspan: 30 ft 6 in
Wing Area: 120 sq.ft
Wing Loading: 6.99 lb/sq.ft
Empty Weight: 450 lb
Gross Weight: 1100 lb
Useful Weight: 650 lb
Fuel Capacity:14 + USGallons
Best Speed: 110 mph
Cruise Speed: 90 mph
Stall Speed @ Gross w/Full Flaps: 35 mph
Service Ceiling: 12,000 ft
Takeoff Distance: 300 ft
Landing Distance: 300 ft
Rate of Climb (gross): 1400 fpm
Maximum Range Fuel Burns: 4.0 USgph
Landing Gear: FG (Tailwheel)
Seats: 1
Cabin Width: 22.75 in
Ultimate “G” Loading: +6.0 – 3.0
Complete Kit Cost (2009): US$ 15,900
Less engine, instruments, fabric, prop

Ultra Pup
Engine: TEC 4 stroke, 60 hp
HP range: 60-80
Speed max: 115 mph
Cruise: 90 mph
Range: 390 sm
Stall: 37 mph
ROC: 1500 fpm
Take-off dist: 200 ft
Landing dist: 200 ft
Service ceiling: 12,000 ft.
Fuel cap: 14 USG
Weight empty: 450 lbs
Gross: 1000 lbs
Height: 5.5 ft
Length: 17.25 ft
Wing span: 30.5 ft
Wing area: 120 sq.ft
Seats: 2
Landing gear: tail wheel.

Ultra Pup
Engine: 2180 cc VW Conversion
Propeller: 62 x 28
Horsepower: 60 – 80
Overall Length: 17 ft 3 in
Height: 5 ft 6 in
Wingspan: 30 ft 6 in
Wing Area: 120 sq.ft
Wing Loading: 6.99 lb/sq.ft
Empty Weight: 450 lb
Gross Weight: 1100 lb
Useful Weight: 650 lb
Fuel Capacity: 14 + USGallons
Top Speed: 115 mph
Cruise Speed (75% power): 80 mph
Stall Speed @ Gross w/Full Flaps: 35 mph
Service Ceiling: 12,000 ft
Takeoff Distance: 300 ft
Landing Distance: 300 ft
Rate of Climb (gross): 1400 fpm
Maximun Range: Up to 350 Miles
Cabin Width: 24.75 in
Ultimate “G” Loading: +6.0 – 3.0
Landing Gear: FG (Tailwheel)
Seats: 2 – Tandem
Complete Kit Cost (2009): US$ 17,295
Less engine, instruments, fabric, prop

North Wing Freedom

The Freedom is a curved tip, high aspect ratio Hang Glider with 35% double surface. Designed for a quick set-up, very easy to fly, comfortable in active air, and performs substantially better than modern training hill gliders.
The Freedom is a modern performance design “single surface” glider. Full length mylar-reinforced leading edge, nose cone, and a king post hang system provides light bar pressure for X-C flying, in three sizes.

The sail design of the Freedom controls twist to get performance without locking up the sail and subsequent handling problems. The standard sail is made with 4.1 oz medium finish Dacron sailcloth. There is also full race sail option, using Mylar (PX10) in the main body.

The Freedom uses 7075-T6 tubing for the mainframe and ribs, imported from Europe, and 6061-T6 seamless drawn domestic tube.

Freedom 150
Double Surface: 35%
Area: 148 square feet
Span: 30.12 feet
Aspect Ratio: 6.0
Number of Ribs: 13 Top
Frame Material: 7075
Rib Material: 7075
Glider Weight: 48 lb
Control Frame: 60 in
Pilot Hook-In Weight: 120-200 lb
USHPA Rating: 2
Suggested Retail Price 2009: $3990

Freedom 170
Double Surface: 35%
Area: 171 sq.ft / 15.9 m²
Span: 32.6 ft / 9.9 m
Aspect Ratio: 6.2
Number of Ribs: 15 Top
Frame Material: 7075
Rib Material: 7075
Glider Weight: 54 lb / 24 kg
Control Frame: 60 in
Pilot Hook-In Weight: 155-235 lb / 70-107 kg
USHPA Rating: 2
Suggested Retail Price 2009: $3990

Freedom 190
Double Surface: 35%
Area: 188 square feet
Span: 34.8 feet
Aspect Ratio: 6.4
Number of Ribs: 14 Top
Frame Material: 7075
Rib Material: 7075
Glider Weight: 57 lb
Control Frame: 60 in
Pilot Hook-In Weight: 195-275 lb
USHPA Rating: 2
Suggested Retail Price 2009: $4090

North Wing Horizon

The 2005 North Wing Intermediate Horizon ET is designed to bring the new pilot far into the sport by offering outstanding performance in tight sail setting with pull of the VG line, and docile handling in loose settings to go right from the training hill to fun soaring. The Horizon ET is stable under tow, even without a stabilizer tail. The set up time is about 10-minute.

The Horizon ET has the easy-to-fly concept in this double surface novice wing, using elliptical fiberglass tips, and with the pull of the VG, exciting top-end performance.

Horizon ET 160

Horizon ET standard features include light weight 7075 air frame, strong 7075 ribs, elliptical curved tips, airfoil kingpost, airfoil downtubes, and variable geometry.

Horizon ET 160
Wing Area: 164 sq.ft / 15.3 m²
Wing Span: 31 ft / 9.4 m
Aspect Ratio: 5.8 : 1
Double Surface: 60 %
Number of Ribs: 13 Top
Rib Material: 7075
Frame: 7075
Glider Weight: 50 lb / 26 kg
Control Frame: 60 inches
Pilot Hook-In Weight: 130 – 240 lbs.
USHGA Rating: 2
Leading Edge Color: PX20
Undersurface Color: White, Red
Main Body Color: White
Sail Area: 165 sq. ft.
Glider Weight: 57 lbs.
Pilot Hook-in Weight: 130 – 230 lbs.
Skill Level: Novice SS/DS
Double Surface KP/TL: Kingpost
VG: Yes

Horizon ET 180
Wing Area: 185 s.ft / 17.5 m²
Wing Span: 33.5 ft / 10.2 m
Aspect Ratio: 5.9 : 1
Double Surface: 60 %
Number of Ribs: 15 Top
Rib Material: 7075
Frame: 7075
Glider Weight: 55 lb / 27 kg
Control Frame: 60 inches
Pilot Hook-In Weight: 160 – 280 lbs.
USHGA Rating: 2
Leading Edge Color: PX20
Undersurface Color: Red, Black
Main Body Color: White
Sail Area: 189 sq. ft.
Glider Weight: 60 lbs.
Pilot Hook-in Weight: 180 – 255 lbs.
Skill Level: Novice SS/DS:
Double Surface KP/TL: Kingpost
VG: Yes

North Star Aerial Service Loomis Special

The 1926 Loomis Special was a redesign by C G Taylor of another plane for barnstormer Jack Loomis (Taylor’s flight instructor). With a steel tube fuselage, Clark-Y wing, and two place cabin under a monoplane wing. Registered N2594 c/n 2, powered by a 120hp Anzani, it crashed in August 1927, and rebuilt as a four place open cockpit with a 135hp Hallett and reregistered N2954.

Engne: 120hp Anzani
Wingspan: 40’0″
Length: 24′

Northstar Viking

Single seat single engined biplane with two-axis control. Wings have swept back leading and trailing edges, and constant chord; no tail, canard wing. Pitch control by fully flying canard; yaw control by tip rudders between wings; no separate roll control; control inputs through stick for pitch and pedals for yaw. Wings braced by struts and transverse X cables; wing profile; double surface. Undercarriage has three wheels in tricycle formation; glass fibre suspension on main wheels. Push-right go left nosewheel steering independent from yaw control. Brake on nosewheel. Aluminium tube framework, without pod. Engine mounted between wings driving pusher propeller.

Shown at Sun ‘n’ Fun in March 1983 at Lakeland, Florida, the Viking is a variation on the famous Easy Riser theme.Whereas UFM of Kentucky has fitted the Easy Riser with a conventional tail giving rise to the Aeroplane (a 1983 model), Northstar had preferred a canard of variable incidence, thus acting as an elevator, for its Viking.

Designed for cross countries, it gives its pilot comfort and a large speed range. Its Kawasaki TA440 is equipped with an electric start, making it necessary to have a 12 V battery on board. The fuel tank is moulded into the seat back, whose structure is of glass fibre, and other nice touches include a twin blade ground adjustable variable-pitch propeller and a rudder bar which is adjustable according to the height of the pilot. Northstar supplies its Viking in kit form requiring 75 100 h for assembly at an introductory price (March 1983) of $5395. The kit does not require any special tools, assembly being largely with pop rivets.

Engine: Kawasaki TA440, 38.5hp at 6000rpm
Propeller 60 in / 1.52 m ground adjustable) inch
Micro V belt reduction, ratio 2.25/1
Max static thrust 235 lb, 107 kg
Power per unit area 0.22 hp/sq.ft, 2.4 hp/sq.m
Fuel capacity 5.0 US gal, 4.2 Imp gal, 18.9 litre
Wing span 32.0 ft, 9.75 m
Total area of main wings 170 sq.ft, 15.8 sq.m
Nosewheel diameter overall 16 inch, 41 cm
Main wheels diameter overall 20 inch, 51 cm
Empty weight 244 lb, 11.1kg
Max take off weight 502 lb, 228 kg
Payload 258 lb, 117 kg
Max wing loading 2.95 lb/sq.ft, 14.4 kg/sq.m
Max power loading 13.0 lb/hp, 5.9kg/hp
Load factors +5.0, 3.0 design
Max level speed 54 mph, 87 kph
Never exceed speed 55 mph, 88 kph
Max cruising speed 45 mph, 72 kph
Stalling speed 23 mph, 37 kph
Max climb rate at sea level 800 ft/min, 4.1 m/s
Best glide ratio with power off 7/1