At the same as the Breguet 16 was being developed, a two-seat fighter, a version of the Breguet 14, was being built. It had originally been on the drawing board back in 1916, and had been submitted to the STAe for consideration. Rejected by them, the design had stayed on the drawing board, but the requirement for a long-range escort fighter at the beginning of 1918 caused it to be resurrected.
An enlarged version of the Breguet 14 appeared at the beginning of 1918, the Breguet 16 Bn2. This was designed for use as night-bomber, and the increased wingspan of 17m enabled it to carry sufficient fuel for long missions, as well as armament for major attacks.
The Breguet 16 had three pairs of inter-plane struts either side instead of two, and differently shaped vertical tail surfaces.
Maximum bomb load was 550kg. Breguet 16s remained in service in Morocco and Syria until March 1927.
The Breguet 13, or AV 1, as it was known at the time, had a conventional look. The prototype took to the air on 21 November 1916 powered by a 220 hp Renault engine, with Louis Bleriot at the controls. After extensive trials by company test pilots, the aircraft was delivered to Aviation Militaire in January 1917 for their assessment. It immediately became apparent that the aircraft was far in advance of anything the British or the Germans had.
The STAe (Section Technical Aeronautique) had stipulated earlier in November that they wanted four types of aircraft, a three seat, long-range reconnaissance plane, a three-seat bomber, a two-seat army co-operation plane, and a two-seat fighter. Breguet submitted the aircraft stating variants of the aircraft could cover all the requirements.
The Breguet 14 has two-bay wings, each with two aluminium spars, wooden leading-edge and ribs and fabric covering. The fuselage was of aluminium tube with fabric covering, except for metal top decking around the cockpits. Tail surfaces were fabric covered steel-tube structures. Conventional controls, with ailerons on the top wing only. Full span flaps on the lower wings dropped automatically at 70 mph to increase lift. Fuel was in two fuel tanks aft of the engine.
The 14B.2 bomber version was fitted with Michelin bomb racks.
Breguet factory in 1918 assembling XIV A2
On 6 March 1917, impressed by the aircraft, the Aviation Militaire ordered 150 Breguet AV 1s (Breguet 13) to be used for reconnaissance. At the same time, the Michelin Company received an order for 150 Breguet AV 2s (Breguet 14), the bomber version. Because the aircraft were almost identical, it was decided to use the same designation for both – Breguet 14. In the months up until September 1917, orders totalling another 475 aircraft were placed.
Because demand was now outstripping supply, other companies were brought in to build the Breguet 14 under licence: Ballenger (3), Darracq (330), Farman (22), Sidam (300) and Paul Schmitt (275). The Paul Schmitt Company was already in the process of building a bomber, but the Breguet 14 had to take precedence, although they still managed to complete their own orders.
As far as the military was concern, the Breguet 14 was adaptable. It underwent numerous modifications, none of which affected its performance. On some of the aircraft, the wingspan and flap size was reduced. Different engines were tried, and various types of armament were installed and tested. Among these was one of the first air ambulances – the Breguet 14S (Sanitaire). The fuselage was modified to enable two stretchers to be carried inside.
Almost every escadrille was supplied with the Breguet 14, including the overseas units. During the short period of the war in which the USAS was involved, they purchased almost 400 of the aircraft. The first of their bombardment units, the 96th Aero Squadron carried out their first mission in June 1918 using Breguet 14 bombers.
Renault 300 hp and metal fuselage
Powered by a Renault 12 Fcy water-cooled inline engine of 300hp / 238.5kW, the metal cowling was extensively louvred and a distinctive frontal radiator was fitted. The pilot was seated in the front and the gunner/observer behind. The Bre 14 A2 was armed with a single 7.7mm forward-fixed Lewis machine gun on the left side of the fuselage and an additional set of 7.7mm Lewis machine guns on a mounting in the rear cockpit. External stores could be carried when in the full bomber role.
Breguet XIV Observer position and camera
The prototype flew for the first time on 21 November 1916.
Türk Hava Kuvvetleri assembled 16 Bréguet XIV A-2 in 1924 for the Turkish Air Force.
The reconnaissance version was followed into production by the bomber in the summer of 1917, the latter differing in having Breguet-designed automatic trailing-edge flaps on the lower wings and transparent panels in the sides of the observer’s cockpit. Late production examples of both versions had horn-balanced ailerons, the B2 aircraft thus equipped doing away with the trailing-edge flaps.
Breguet XIV A2 camera position
The B2 version could be fitted with an additional Lewis gun that fired downwards through the rear fuselage floor and had a maximum bomb load of 256kg, carried on underwing racks. A single-seat long-range version, known as the Bre 14 B1, was also built in limited numbers during 1918, and was intended to bomb Berlin. In fact it was little used and never mounted an attack on the German capital. Breguet 14 also equipped American and Belgian units during World War I, some powered by Italian Fiat A-12 and A-12bis engines. The Bre 14 A2 reconnaissance version and the Bre 14 B2 bomber equipped at least 71 French escadrilles on the Western Front by November 1918 and were also used by units in Serbia, Greece, Macedonia and Morocco. Many ex-French aircraft were handed over to Poland in 1919 and these took part in the fighting with Russia in 1920. The type formed part of the initial equipment of the Czech air arm, and others were operated in Brazil, China (70 with 298kW Lorraine-Dietrich engines), Denmark, Finland, Greece, Japan, Portugal and Spain. The Spanish equipped four squadrons in Morocco in 1922, using them on missions against Riff tribesmen. A further 40 were obtained in 1923. A small number of float variants were also built, mostly with a central main float and small wingtip stabilising floats. During 1919 Breguet 14 made a number of long-distance flights and Louis Breguet founded the Compagnie des Messageries Aeriennes with them, making regular air mail flights linking Paris with Brussels and London. These Bre 14 had special mail containers fitted under the wings. A cabin version with provision for two passengers was built as the Breguet 14T. Later came the improved Bre 14Tbis and the three-passenger Breguet 14T2. During the 1920s, the Lignes Aeriennes Latecoere company used more than 100 Breguet 14 in various versions on its routes between Toulouse and Dakar (West Africa) and between Natal and Santiago di Chile in South America. The Br 14S air ambulance, adapted from the Breguet 14T, was widely operated in the 1920s during the campaigns in Morocco and Syria. Each could carry two stretchers in the rear fuselage.
The Forges et Ateliers de Construction Latecoere began its interest in aviation in 1917 with an aircraft works at Toulouse-Montaudron. In 1917 P-G Latécoère turned from making munitions to licence-building aircraft for the Aviation Militaire Française. Total wartime production amounted to 800 licenced Breguet XIV and Salmson 2A.2 2-seat reconaissance bomber biplanes.
Initially, these licenced airframes do not seem to have received Latécoère designations. The licenced XIVs were refered to as Breguet-Latécoère 14s (or sometimes Latécoère Breguets). The designation Laté 1 may have been applied to licenced Brequets but there is some confusion with a 1918 2-seat fighter (of original Latécoère design?).
Latécoère converted large number of Breguet XIVs for civilian used in 1921-23 (190 for use by Aéropostale alone). None of these civil conversions seem to have received distinct Laté-x designations. Namings were as follows:
The ‘Torpedo’ name comes from the designation of Breguet’s own 14T and 14Tbis passenger conversions. Like the 14Ts, the Breguet-Latécoère 14 Torpedo was an aft cabin conversion as distinct from the cabin 14 ‘Salon’ conversions.
Breguet XIX TF Super Bidon Point d’Interrogation
Production was spread over seven manufacturers, in addition to the Louis Breguet factory at Velizy, near Paris, and 7800 of the type were built up to 1926, more than 2,500 appearing after the war ended in 1918.
The Breguet 14s were sold to 22 countries. There were fourteen variations that included using a number of engines and a large number of modifications. The type would continually see service in frontline French forces up until 1932.
Br.13 Engine: 1 x Gnome, 160 hp Wingspan: 49 ft 7 in / 15.3 m Length: 27 ft 10 in / 8.5 m Height: 10 ft 9 in / 3.3 m Empty weight: 2094 lb / 950 kg Loaded weight: 2876 lb / 1350 kg Max speed: 62 mph / 100 kph Armament: 1 x Hotchkiss mg Bombload: Flechettes
Breguet Bre.14A Engine: 1 x Renault 12Fcx, 220kW Wingspan: 14.4 m / 47 ft 3 in Length: 9.0 m / 29 ft 6 in Height: 3.3 m / 10 ft 10 in Wing area: 49.0 sq.m / 527.43 sq ft Take-off weight: 1740 kg / 3836 lb Empty weight: 1140 kg / 2513 lb Fuel capacity: 57.2 gal Max. speed: 180 km/h / 112 mph Ceiling: 6000 m / 19700 ft Range: 900 km / 559 miles Crew: 2 Armament: 3 machine-guns, 300kg of bombs
Breguet Bre.14B2 Engine: 1 x Renault 12 Fcy water-cooled inline, 300hp. Length: 29.10ft (8.87m) Wing span: 48.92ft (14.91m) Height: 10.83ft (3.30m) Empty Weight: 2,282lbs (1,035kg) Maximum Take-Off Weight: 3,483lbs (1,580kg) Fuel capacity: 57.2 gal Maximum Speed: 121mph (195kmh; 105kts) Maximum Range: 301miles (485km) Cruise: 75 mph. Service Ceiling: 13,993ft (4,265m; 2.7miles) Armament: 1 x 7.7mm Lewis machine gun in forward-fixed firing position. 2 x 7.7mm Lewis machine guns on mounting in rear cockpit. Up to 573lbs of external ordnance. Accommodation: 2 Hardpoints: 4
Breguet XIX Super Bidon Point d’Interrogation Engine: Hispano-Suiza 12 LB, 650 hp Wingspan: 18.30 m Length: 10.72 m Height: 4.08 m Wing area: 59.94 m² Max weight: 6375 kg Max speed: 250 km/h Ceiling: 6700 m Range: 9000 km
The Breguet 11 Corsair was a three engined aircraft with two pushers and one tractor. The two pusher engines were mounted on the lower wing, either side of the main fuselage, in nacelles, each with its own tricycle undercarriage. The three-bay, unequal span wings had ailerons mounted in the upper wings, but despite a favourable test report, the aircraft was declined in favour of smaller models. The 90-ft (27.6m) wingspan was one of the reasons it was declined, but it was felt that the relatively slow speed of the aircraft, 91 mph (149 kph), coupled with its enormous size made it an easy target for anti-aircraft guns.
Towards the end of the 1920s Louis Breguet returned to the study of helicopters and in 1929-30 took out patents for systems for stabilising aircraft of this type while in flight. In 1931 Louis Breguet formed the Syndicat d’Etudes du Gyroplane, with Rene Dorand (who had joined the Breguet company in 1924) as technical director, and began the design and construction of an experimental machine known as the Gyroplane Laboratoire.
In 1935, with the cooperation of René Dorand, Louis Breguet completed the coaxial Gyroplane Laboratoire, which was the first helicopter to meet the aviation industry’s control and performance expectations for a practical design. Returning to his lifelong fascination with helicopters, an older Louis Breguet oversaw but did not participate directly in the construction and testing of this compact single-seater.
Intended originally to be powered by a 240hp Breguet-Bugatti engine, it consisted basically of a steel-tube open framework supporting the engine, fuel tank, flight controls and pilot, with rear booms carrying the plywood-covered tail surfaces. An unusually wide track main undercarriage was mounted on outriggers from the central framework, with a small tailwheel and a nosewheel to prevent the machine tipping forward on landing. The transmission from the big radial engine drove a pair of co-axial, counter-rotating, 2-blade metal rotors whose blades had an aerofoil section and an unusually large diameter. One rotor shaft turned inside the other, each rotor thus cancelling out the torque created by the other. Novel features for the time were the use of a cyclic pitch control for lateral and longitudinal movement, and collective pitch for movement in the vertical plane.
The Gyroplane was badly damaged in a ground accident at the end of 1933. Rebuilt with extensive modifications and tested conservatively on the ground, it resumed flight tests in June 1935. Breguet then committed it to maneuvering, speed, altitude, and endurance requirements far in excess of anything so far accomplished by a helicopter.
The Gyroplane Laboratoire set four world records in 1936 when test pilot Maurice Claisse flew the craft at 98 kph (61 mph) (September 11), to a height of 158 m (518 ft), over a distance of 43 km (27 miles), and for a duration of 62 minutes.
In 1937 (after a similar achievement by the Fw 61 in Germany) it made its first ‘engine off’ landing using autorotation. The Gyroplane was badly damaged in June 1939 during autorotation tests. It was subsequently destroyed by Allied bombing of historic Villacoublay Airfield in 1943.
It is not certain whether the Bugatti engine was ever installed; the aircraft did most or all of its flying with the more powerful Hispano engine.
Engine: Hispano-Suiza, 225kW Rotor diameter: 15.89m Length: 8.92m Height: 2.79m Max take-off weight: 1950kg Empty weight: 1430kg Speed: 98 kph (61 mph) Ceiling: 158 m (518 ft Range: 43 km (27 miles) Endurance: 62 minutes. Crew: 1
Developed during 1914 when French military planners began to express a preference for pusher- over tractor-configured aircraft, leading Breguet to cease further development of its original Type IV design and pursue military contracts with an aircraft of the preferred layout. The Bre.4 evolved indirectly from the BU3 two-seat twin-boom pusher biplane of late 1914 as a smaller and lighter development of its bomber derivative, the BUM (B=Breguet, U=Salmson engine and M=Michelin-built), the BUC (the letter “C” signifying Chasse) was intended primarily as a bomber escort. The Type IV was a two-bay, equal-span, unstaggered biplane that seated the pilot and observer in tandem open cockpits in a nacelle that also carried the pusher engine at its rear, and the tricycle undercarriage. As the prototype neared completion, the Breguet factory at Douai was threatened by the advancing German Army, and the machine and its builders were evacuated to Villacoublay where construction and testing were completed. At this point, André and Édouard Michelin approached the French government with an offer to sponsor the construction of 100 bombers for the Army, and were awarded a licence to the Breguet design. This was put into production as the BUM (B for pusher-driven, U for Canton-Unné-powered, M for Michelin), and later revised to the BLM as the definitive Renault-powered version. With the installation of a 220hp Renault 12Fb 12-cylinder water-cooled engine in place of the Salmson, prototype trials were performed in June 1915, a few additional aircraft being built under the designation BLC. Soon after the BUM had entered service, the French Army requested that an escort fighter version be developed to protect the bombers from interception. Breguet responded with a lightened design armed with a 37 mm (1.46 in) Hotchkiss cannon on a flexible mounting in the forward cockpit of the fuselage nacelle intended to pick off enemy fighters before they closed to within range of their machine guns. This entered production as the BUC (C for chasse, or pursuit) in its original 200hp Salmson Canton-Unné 14-cylinder radial powered version and BLC in its Renault version. Few of these escort fighters were built, as their performance and utility were discovered to be lacking, and the doctrine of the cannon-armed escort fighter was soon abandoned in favour of countering fighters with other similar fighters. A number of BUCs were also built for Britain’s RNAS using British engines. The performance of both the BUC and BLC versions of the Breguet de Chasse was unspectacular and, with fewer than 20 delivered, they were declared obsolete by the Aviation Militaire before the end of 1916. During that year, a 17 essentially similar aircraft were supplied to the Royal Naval Air Service. These differed from the BUC/BLC primarily in having the 225hp Sunbeam Mohawk 12-cylinder engine, armament being a single 7.7mm Lewis machine gun (which was an alternative weapon to the Hotchkiss on French machines). The RNAS was disappointed with the performance of the Breguet de Chasse, which proved unsuitable for employment in the fighting role, and the service withdrew the type from its first-line inventory in June 1916.
BLC Take-off weight: 1535 kg / 3384 lb Empty weight: 1160 kg / 2557 lb Wingspan: 16.40 m / 54 ft 10 in Length: 9.50 m / 31 ft 2 in Height: 3.70 m / 12 ft 2 in Wing area: 54.0 sq.m / 581.25 sq ft Max. speed: 138 km/h / 86 mph
Variants: Type IV (BU3) Breguet prototype. BUM (BrM2B.2) Michelin-built, Canton-Unné-powered bomber version. BLM (BrM4B.2) Michelin-built, Renault-powered bomber version. BUC Michelin-built, Canton-Unné-powered escort fighter version. BLC Michelin-built, Renault-powered escort fighter version. Breguet de Chasse Version of BLC for RNAS, powered by Sunbeam Mohawk or Rolls-Royce Falcon engine.
The Breguet LE (Laboratoire Eiffel) single-seat fighter monoplane was aerodynamically an advanced design with emphasis being placed on minimising drag in order to achieve high performance. The basis of the design was produced by the Director of the Laboratoire Eiffel in collaboration with the Breguet design staff, the Breguet company having overall responsibility for translating the basic concept into a prototype. The first prototype LE was fitted with a 180hp Hispano-Suiza 8Ab eight-cylinder water-cooled engine. Proposed armament consisted of a single 7.7mm Vickers machine gun totally enclosed within the fuselage, although this was never fitted. The LE made a short initial flight at Villacoublay in mid-March 1918, but the undercarriage failed on landing. After repairs, a further flight was made on 28 March, this terminating when the aircraft dived into the ground at full throttle, the pilot, Jean Saucliere, losing his life. Developments of the LE with a 220hp Lorraine-Dietrich and a 300hp Hispano-Suiza 8Fb were proposed, and construction of an airframe to take the latter power plant was nearing completion at the time of the loss of the first prototype, when further work was suspended.
LE Engine: 180hp Hispano-Suiza 8Ab Take-off weight: 700 kg / 1543 lb Empty weight: 495 kg / 1091 lb Wingspan: 9.78 m / 32 ft 1 in Length: 6.35 m / 21 ft 10 in Height: 2.00 m / 7 ft 7 in Wing area: 20.0 sq.m / 215.28 sq ft Max. speed est: 220 km/h / 137 mph
The Type 6 (Bre 6 Ca2) two-seat escort fighter of 1916 was a 225hp Salmson A9 water-cooled nine-cylinder radial engined counterpart of the Renault-powered Type 5, and resulted from a fear that Renault engine production would prove inadequate to meet demands. The Type 5 airframe was modified to take the Salmson engine mounted immediately above the rear undercarriage legs and driving the propeller by means of an extension shaft, the power plant being entirely enclosed. Armament of the Type 6 fighter normally consisted of a short-barrel 37mm Hotchkiss cannon in the forward fuselage. Performance, weights and dimensions were essentially similar to those of the Type 5.
The relative success of the use of cannon in the Breguet BU.3 led the Breguet company to install it in their latest aircraft, the Breguet 5. This was a three-bay, unequal span biplane powered by a 225-hp Renault 12Fb engine. The tail section was the same as that of the Breguet BU.3, with four tail booms extending from the upper and lower wings. The Breguet Br.M5 series of biplane bomber was developed from the Breguet Br.M4 late in 1915 and was regarded by the Aviation Militaire as a two-seat escort fighter or reconnaissance-fighter.
The Br.M5 was operated by a crew of two with the pilot seated in the middle of the aircraft and the gunner/observer to the front. The engine sat behind the crew area – directly behind the pilot and was a pusher driving a two-blade propeller. Design was with a bathtub-like fuselage, a static tricycle landing gear array and framework and cables leading out to the empennage.
The RNAS purchased 59 Breguet 5s from the Breguet factory and ordered an additional 3 from Graham-White Aviation Company (as Grahame-White Type XIX / G.W.19), but only 10 were ever built in Britain. Twenty-five of the Breguet 5s built in France had the 250-hp Rolls-Royce engine installed, the remaining models were powered by the 225-hp Renault engine.
In action, the Br.M5 was fielded primarily as a night bomber and used by both the French and English forces from 1916-1917 though it first appeared in the summer of 1915. The Type 5 fighter, or Bre 5 Ca2, never equipped a complete escadrille, a few aircraft of this type being issued to each of the units operating the Bre 5 B2 bomber version, for which it was expected to act as escort. Armament comprised a 37mm Hotchkiss cannon on a flexible mounting in the forward cockpit and a rear-firing 7.7mm Lewis gun on an elevated mounting over the leading edge of the upper wing. Eleven Type 5 fighters were operational with the Aviation Militaire by 1 February 1916, but the type was generally unpopular.
Bre.12
Breguet Br.M5 Engine: 1 x Renault 12Fb, 220hp or 1 x Rolls-Royce Eagle, 250hp. Wingspan: 17.50 m / 57 ft 5 in Length: 9.90 m / 33 ft 6 in Height: 3.90 m / 12 ft 8 in Wing area: 57.70 sq.m / 621.08 sq ft Take-off weight: 1890 kg / 4167 lb Empty weight: 1350 kg / 2976 lb Max. speed: 133 km/h / 83 mph Service Ceiling: 11,483ft (3,500m; 2.2miles) Armament: 1 x 7.7mm Lewis machine gun or 1 x 37mm cannon in forward observer/gunner position. Accommodation: 2 Hardpoints: 2
Breguet-Michelin 5 Engine: Renault, 220 hp Wingspan: 57 ft 8 in Length: 26 ft 1 in Max weight: 4235 lb Speed: 86 mph at SL Endurance: 5 hr Armament: 1 x mg, 1 x 37 mm cannon Bombload: 660 lb Crew: 2
Breezer is an ultra light, LSA, and experimental category design. The entire cockpit was designed ergonomically; from the instrument panel to the seating arrangement, everything was modeled and shaped. Planning for a Breezer kit plane version from day one, the aluminum airframe structure design was kept simple and sturdy. To assemble the pre-manufactured components, you only need a flat table top. The high level of prefabrication allows a rapid fuselage assembly. Accurate matched drilling lets you to assemble aluminum alloy parts without extensive jigging. Other parts, like the spar center section, are provided fully assembled. Wherever needed the fuselage is reinforced in an optimal way. The wings are built in a spar/rib structure. As the wings sport no wash-out, neither aerodynamically nor geometrically, these can be built on a flat table top. Jigging is minimal. Like with the fuselage, the wing parts come with most holes match drilled into the ribs, spar and wing skin. This assures that assembly errors are eliminated from the outset. This same simple and sturdy structure is used to assemble the horizontal stabilizer and elevator. The Breezer experimental category kit plane was developed along with the ultralight. The following items were modified for the experimental category kit plane:
MTOW raised to 580 kg / 1279 lb
Stronger wing spar
Stronger wing spar center section
Stronger stabilizer (as requested by the Swiss) After Germany allowed sailplanes to be towed by ultra light aircraft, the Breezer was tested and found suitable for towing flights. The Breezer is made in three models. The Breezer CR. The Breezer Club as a dedicated flight training edition, and the Breezer Acro, aerobatic aeroplane.
Breezer II
In 2012 the all-metal Breezer II was available as a ready built or E-LSA kit airplane. Price 2012: S-LSA Breezer is US$125,800. Quick Build kit (less engine and avionics): US$46,600.
Engine: Rotax 80 hp Cruise speed (75%): 180 km/h / 112 mph Maximum Speed Vne: 245 km/h / 152 mph Stall speed: 64 km/h / 40 mph Climb speed: 4,5 m/s / 886 fpm Wingspan: 8,03 m / 26.4 ft Cabin width: 1,16 m / 45,7 in Length: 6,40 m / 21 ft Height: 2,15 m / 7 ft Wing area: 10,92 sq.m / 117.5 sq ft Empty weight incl. BRS: 296 kg / 652.6 lb Maximum gross weight: 472,5 kg / 1041.7 lb Load: 176,5 kg / 389 lb Fuel capacity: 70 liter / 18.5. USgal Average fuel consumption / hr: 11-14 lt / 2.9 -3.7 USgal Take off dist: 135 m / 443 ft Landing dist: 140 m / 459 ft
Engine: Rotax 100 hp Cruise speed (75%): 200 km/h / 124 mph Maximum Speed Vne: 245 km/h / 152 mph Stall speed: 64 km/h / 40 mph Climb speed: 6 m/s / 1181 fpm Wingspan: 8,03 m / 26.4 ft Cabin width: 1,16 m / 45,7 in Length: 6,40 m / 21 ft Height: 2,15 m / 7 ft Wing area: 10,92 sq.m / 117.5 sq ft Empty weight incl. BRS: 300 kg / 661.4 lb Maximum gross weight: 472,5 kg / 1041.7 lb Load: 172,5 kg / 380 lb Fuel capacity: 70 lt / 18.5 USgal Average fuel consumption / hr: 12-15 / lt / 3.1-3.9 USgal Take off dist: 95 m / 312 ft Landing dist: 140 m / 459 ft
Breezer II Engine: Rotax 912 ULS, 100hp@SL Propeller: 3-blade Neuform Gross weight: 1320 lb Empty weight with optional BRS: 763lb Useful load, std: 557 lb Payload, full std. fuel: 518lb Fuel capacity (lbs.): 21 Wing area: 117.5 sq. ft Cruise speed, 75% power: 105 kt Range with 30-min. reserve, 75% power: 420 nm Best rate of climb, solo: 1181 fpm Best rate of climb, two people: 900 fpm Service ceiling: 14,500 ft Takeoff over 50 ft obstacle: 925 ft Landing ground roll: 606 ft Vne: 120 kt V Stall: 36 kt