Brown Special Monoplane Racer

Alden Brown incorporated some novel features in his Racer NR71Y #203. The cockpit enclosure had no break or reversal in the fuselage contour. Top of the transparent enclosure was faired into the body lines and the fuselage forward of the cockpit was cut down at an angle of about 10 degrees with the fuselage centreline. Vision forward was poor during ground operations and still marginal in the air.

The Brown had been designed for a retractable undercarriage but time did not permit its installation, so it was fitted with cantilever struts and completely enclosed wheels. It was painted a light blue.

Alden Brown’s plane suffered a mishap on its first take-off at the Nationals. Roy Minor was at the controls. The close fitted wheel pants filled with mud and locked the wheels, causing the ship yo rear up enough to damage the cowl and propeller. As it came to rest the gear also collapsed so the ship was out of competition for the balance of the races.

Lee Shoenhair was the pilot in 1933. During the early part of the year he and Alden experimented with a retractable gear but were unable to get it to function properly so they reverted to the original gear. Lee was careful about use of the wheel pants and when in question on a slightly muddy or rough field these were not used. The aircraft appeared as often in 1933 without wheel pants as it did with them. She now wore the Gilmore Oil insignia and a dorsal tail fin with a small headrest above the glassed-in cockpit enclosure. This improved lateral stability and increased the pilot’s vision. The racer placed fourth in the 1000 cubic inch displacement free-for-all at the Nationals. During this race Lee experienced super-charger trouble with the engine and achieved only 137.52 mph. This was the last year the Alden Brown Racer appeared at the races. After that its whereabouts are unknown.

Model 203’s wing span was 18-19 feet and its length about the same.

Brotero Bichino / IPT IPT-0

Designed as a private venture in the late ‘thirties, the Bichino subsequently served as a test-bed for the IPT (Instituto de Pesquisas Tecnológicas or Technological Research Institute) of the São Paulo State University. Four examples were built. In 1938, the IPT’s Aviation Research Department was, by a fair margin, the most important aviation research centre working in Brazil and had completed a long series of studies of the use of native Brazilian woods in aircraft. A special technique had been developed for producing in industrial quantities a new kind of plywood for aircraft using Brazilian pine, and studies had been made of freijo, a Brazilian hardwood 20 per cent stronger and heavier than spruce. One of the principal researchers at the IPT was Frederico Abranches Brotero, who was also a gifted aircraft designer. In company with Orthon Hoover, an American who had come to Brazil as a demonstration pilot for Curtiss in 1911 and had decided to stay, Brotero set about putting freijo and the new plywood to the test in a light aircraft. Work on Brotero’s tiny wooden aeroplane, designed around a 60 hp Walter Mikron engine, began late in 1939 in a workshop of the São Paulo Polytechnic School under IPT supervision and it was transferred to Rio Claro city aero club for completion and first flight. The latter was effected in 1940. The Little Bug was of all wood construction, the cantilever low-wing being a two-spar structure with a Clark Y aerofoil; the spars were of paumarfim, ribs of freijo and covering of Brazilian pine plywood. Ailerons were fabric covered; fixed letter-box slots were incorporated ahead of the ailerons and split flaps extended along each trailing edge from aileron to fuselage. The wooden monocoque fuselage structure had guapuruvu longerons and freijo reinforcements with plywood construction. Tail unit construction was of freijo with fabric covering for the elevators and rudder; there was a controllable trim-tab in the starboard elevator. The fixed landing gear had rubber-in-compression shock absorbers and a steel tail skid. Phenolic resin was used to bond the wooden components. The open cockpit was just wide enough for a pilot of average build, but was comfortable and afforded good visibility. In 1943, the Bichino prototype (PP-THH) was purchased by the IPT to be used as a flying test bed and three more examples were put in hand, with some structural redesign to reduce weight and improve performance. The three new Bichinos had 65 hp, 75 hp and 85 hp Continental engines respectively. By this time, IPT had completed other prototypes designated the IPT- 1, IPT-2 and IPT-3, and the Bichino was consequently given the designation IPT-0, the three new examples becoming the IPT-0-A, -B and -C respectively. The fourth and last was completed in 1947 and proved to be the best performer and most pleasant to fly

Broome Le Beau

second aircraft

Ray Broome designed and built two ultralight aircraft in the late 1980s early 1990s based on the Resurgam parameters.

Number one was completed in 1987 as a landplane with a tricycle undercarriage although it was operated on floats for a time. The fuselage of the first aircraft was built solely from fibreglass. It was sold unregistered in 1991 and reconfigured as a taildragger and was still flying in NSW, Australia, as late as mid-2014.

The second aircraft was built in 1992 and took up the registration 10-0046 C/N 2. It was always operated as a floatplane, mostly around the Moreton Bay area until 2008 by which time it had accumulated approximately 330 hours in service.

The fuselages of both aircraft were built on a mould taken from the front section of a damaged Club Libelle glider which inspired the name LeBeau. The composite was 6mm Kevlar foam sandwich. The rear fuselage is an aluminium tube with the tail sections having timber ribs on aluminium spars. The wings similarly have timber ribs with a double sided plywood main spar and plywood nose skin. Wing, rudder and tailplane are covered with Stits aircraft fabric painted in two-pack.

second aircraft

The floats are single skin fibreglass with plywood ribs and sealed flotation chambers. The engine is a 2-stroke, 4-cylinder Konig SD-570, rated at 28hp at 4200 rpm with a toothed belt reduction drive. The propellor is a 3 bladed ground adjustable in pitch. A third nose cone and fuselage was moulded but not taken any further.

second aircraft

The second aircraft was delivered by road to QAM Caloundra by the builder/donor Ray Broome.

second aircraft
Engine: Konig SD-570, 21kW (28hp)
Wing Span: 9.75m / 32ft
Wing Area: 11.89sq m / 128sq ft
Wing Chord: 1.22m / 48in
Wing Section: NACA 4415
Length: 5.64m / 18ft 6in
Height: 1.98m / 6ft 6in
Weight Empty: 150.88kg / 337lb
Weight Loaded/MTOW: 258.55kg / 570lb
Fuel Capacity: 35L / 7.7gal
Max Speed: 105km/h / 65mph
Cruising Speed: 96km/h / 60mph
Initial Climb: 122m/min / 400ft/min
Range: 193km / 120mile
Fuel Consumption: 14L/hr / 3.3gal/hr

Brookland Mosquito         

The Brookland Mosquito was a British amateur-built single-seater ultra-light gyroplane first flown in 1962. The Mosquito was powered by a Ernie Brooks-converted Volkswagen four-cylinder horizontally-opposed air-cooled engine providing a top speed of 137km/h, and in a second version 161km/h, and a range of 225km.

September 1968

Versions:
Mosquito Mk.1 Hornet
Mosquito Mk.2
Mosquito Mk.3

Engine: VW 1200cc, 70 hp at 3750 rpm
Rotor diameter: 22 ft
Fuselage length: 12 ft
Height: 6 ft
Weight: 310 lb
Top speed: 80 mph
Cruise: 65 mph
ROC: 750 fpm