The illustrated Viva is located at Holbrook ultralight museum.
Skycraft Viva
Aircraft
Skycraft Scout Biplane
A second version of the Biplane Scout was built by Ron Wheeler.
Skycraft Scout
This Australian design was originally built by Ron Wheeler in 1972 as a powered version of his earlier Tweetie hang-glider design. First flown in May 1974, his friends asked him to build them one and by 1976 demand was so high Ron Wheeler set up Skycraft and full-scale production began in November 1976 after the issuing of the ANO 95.10. The stitching of catamaran sails is still evident in the wing of the very early models. The Scout, later dubbed Mk.1, was considerably cheaper than the other types available mainly because it is smaller and doesn’t offer quite the same performance. It is however more economical and resembles in many ways the very first microlight — the Santos Dumont Demoiselle of 1911. The single surface wire braced taildragger has three-axis control via the all flying tail “feathers and wing warping for roll control. Airframe is constructed from high tensile alloy section extruded from the company’s dies. The aircraft sits high on the main wheels, an advantage for its rough strip capabilities. An engine option was available as well as floats and a cockpit pod, and optional Rotax 377 engine. The floats were designed by Wheeler and added to his aircraft in September 1977. The aircraft with floats was first displayed at the Schofield Air Show in 1978.
A historic aircraft in Australia, being the first type to receive certification under to Ultralight classification. The first to do so is in the Powerhouse Museum in Sydney, Australia.
En route, it has gained a modified front axle and seat support (hence the Mk2 title) but otherwise it is little changed. The same 173cc Pixie Major engine is used, driving a tractor propeller, and controls are two axis, operated entirely by the stick and with no separate roll control for the single surface wing. The Scout Mk.2 was a single seat single engined high wing monoplane with two axis control. Wing has unswept leading edge, swept forward trailing edge and tapering chord; conventional tail. Pitch control by fully flying tail; yaw control by fully flying rudder; no separate roll control. Control inputs through stick for pitch/yaw. Wing braced from above by kingpost and cables, from below by cables; single surface wing. Undercarriage has three wheels in tail dragger formation; steel spring suspension on main wheels. Push right go right tailwheel steering connected to yaw control. No brakes. Aluminium tube framework, without pod. Engine mounted at wing height driving tractor propeller. Stainless steel rigging and control cables. Wing material is heavy duty Dacron.
The combination of very small fuel tank and low maximum speed means that the Scout is more of a fine weather fun machine than an aircraft for cross country flying. Never the less the Scout has won many friends in its seven years of flying, not least because of its 15 minute rigging time, and has earned its place in the history of the sport.
The Scout Mk.3/3/R was a single seat single engined high wing monoplane with conventional three axis control. Wing has unswept leading edge, swept forward trailing edge and tapering chord; conventional tail. Pitch control by fully flying tail; yaw control by fully flying rudder; roll control by wing warping; control inputs through stick for pitch/roll and pedals for yaw. Wing braced from above by kingpost and cables, from below by cables; single surface. Undercarriage has three wheels in tail dragger formation; steel spring suspension on mail wheels. Push right go right tailwheel steering connected to yaw control. No brakes. Aluminium tube framework, without pod. Engine mounted at wing height driving tractor propeller. Stainless steel rigging and control cables. Wing material is heavy duty Dacron. Introduced in 1982 to cater for pilots wanting conventional three axis controls, the Scout Mk3/3/R uses a wing-warping system for roll control. Rudder pedals control yaw and also operate the steerable tailwheel. However, the adoption of three axis control was not the only major change. The Pixie engine was discarded in favour of a 250 Robin, bringing a marked improvement in performance and giving rise to the ‘R’ in the designation title (the second ‘3’ indicates three axis). Typical output for a 250 Robin is 18 hp, but in this application 21 hp is claimed, using an exhaust system engineered specifically for this aircraft. There are also numerous detail engineering changes compared to the Mk2, plus a modified framework which gives better pilot protection.
While the wing warping system has proved effective as a wing levelling device, adverse yaw can be experienced under some circumstances and further modifications to eliminate this have been designed by one of Britain’s Scout dealers as the Flylite (East Anglia) Super Scout.
The Scout Twin Mk.4 was powered by a Rotax 377 engine and featured a fibreglass fuel tank, moulded to the fuselage and over the C of G, and a moulded fibreglass cockpit. The Mk.IV can also be fitted with floats. About 50 of these were built.
Components such as the moulded cockpit will fit the Mk.III as will the dual wire drag system. The aerolastic structure has been truck tested to air loads above 80 mph.
A further enclosed version was built.
And another version place the pilot position above the fuselage.
Variation: Mahe Pfadfinder
Scout Mk.I
Engine: Pixie Major, 14hp at 6500rpm
Propeller diameter 48 inch, 1.23 m
V belt reduction, ratio 3.0/1
Max static thrust 79 lb, 36 kg
Power per unit area 0.13 hp/sq.ft, 1.4hp/sq.m
Fuel capacity 0.6 US gal, 0.5 Imp gal, 2.5 litre
Length overall 17.1 ft, 5.20 m
Height overall 6.2ft, 1.90m
Wing span 28.8ft, 8.77 m
Chord at root 6.5ft, 1.98 m
Chord at tip 1.3ft, 0.40m
Sweepback 0 deg
Tailplane span 10.5ft, 3.2m
Rudder height 4.8 ft, 1.47 m
Total wing area 109 sq.ft, 10.1 sq.m
Total elevator area 12.5 sq.ft, 1.16 sq.m
Wing aspect ratio 17/1
Wheel track 4.5ft, 1.37m
Wheelbase 12.5ft, 3.80m
Tailwheel diameter overall 4 inch, 10cm
Main wheels diameter overall 12 inch, 31 cm
Empty weight 122 lb, 55.5 kg
Max take off weight 297 lb, 135 kg
Payload 175 lb, 79.5 kg
Max wing loading 2.72 lb/sq.ft, 13.4 kg/sq.m
Max power loading 21.21b/hp, 9.65kg/hp
Load factors; >+3.0, > 3.0 ultimate
Max level speed 47 mph, 75 kph
Never exceed speed 75 mph, 120 kph
Max cruising speed 40 mph, 65 kph
Economic cruising speed 40 mph, 65 kph
Stalling speed 20 mph, 32 kph
Max climb rate at sea level 200ft/min, 1.0m/s
Min sink rate 510 ft/min at 40 mph, 2.6 m/s at 65 kph
Best glide ratio with power off 7/1 at 40 mph 65 kph
Take off distance 230 ft, 70 m
Land¬ing distance 100ft, 30m
Service ceiling 9900ft, 3000m
Range at average cruising speed 28 mile, 45 km
Mk.III
Engine: Robin 244cc 2 stroke
Wing Span: 28 ft 6 in (8.8 m)
Wing Area: 149 sq. ft
Cruise speed: 46 mph (75 kmh)
Stall speed: 19 mph (32 kmh)
Max speed: 105 kph
Max. rate of climb: 550 fpm
Empty weight: 130 lb (58.03 kg)
Max. pilot weight: 205 lb (91 kg)
Engine: 244 cc/19 hp Fuji Robin 1-cylinder Two-stroke
Fuel capacity: 19 ltr
Prop: 122cm
Range: 55 miles
3/3/R
Engine: Robin EC25PS, 21 hp at 6500 rpm
Propeller diameter: 48 inch, 1.23 m
V belt reduction, ratio 2.2/1
Max static thrust 130 lb, 59 kg
Power per unit area 0.19 hp/sq.ft, 2.1 hp/sq.m
Fuel capacity 1.6 US gal, 1.3 Imp gal, 6.0 litre
Empty weight 130lb, 59kg
Max take off weight 310 lb, 141 kg
Payload 1180 lb, 82 kg
Max wing loading 2.84 lb/sq.ft, 14.0 kg/sq.m
Max power loading 14.8 lb/hp, 6.7 kg/hp
Load factors design; >+3.0, > 3.0 ultimate
Max level speed 53 mph, 85 kph
Never exceed speed 75 mph, 120 kph
Max cruising speed 47 mph, 75 kph
Economic cruising speed 47 mph, 75 kph
Stalling speed 20 mph, 32 kph
Max climb rate at sea level 550 ft/min, 2.8 m/s
Min sink rate 470 ft/min at 40 mph, 2.4 m/s at 65 kph
Best glide ratio with power off: 7/1 at 40 mph, 65 kph
Take off distance 130 ft, 40 m
Land¬ing distance 100ft, 30m
Service ceiling 9900ft, 3000m
Range at average cruising speed 56 mile, 90 km
Scout Twin Mk.4
Engine: Rotax 377
Empty weight: 82 kg
AUW: 180 kg
Wingspan:8.7 m
Wing loading: 7 kg/sq.m
Takeoff distance: 25-40 m
Landing roll: 24-30 m
Stall: 32 kph
ROC: 600 fpm
Max speed: 100 kph
Cruise: 75 kph
Glide ratio: 7-1
Fuel capacity: 15 lt
Fuel burn: 8 lt/hr
Skycraft Tweetie
In 1974 Ron Wheeler developed the “Tweetie” hang glider. The Tweetie was almost exactly the same as the Scout only it did not have the engine, the tail plane was fixed and the pilot hung from the A-frame below the wing. Apart from being quite a successful hang glider the Tweetie allowed Ron to experiment and get experience with the Scout design.
Skroback Road-plane
In 1934, electrician and hobbyist Frank Skroback built the first airplane that could be driven on a road. Or the first car that could be flown. It has six wings and an overall width of seven feet, so it can fit inside a lane. The plane was to be auctioned at Red Baron’s Antiques in Atlanta circa 2003.
Skonkworks Nemethis
The full sized aeroplane is 16′ x 16′.
Skonkworks 24bis
The 24 Bis (that’s what they call the example you see in the images) is a tribute to Alberto Santos Dumont.
The Winchester Skonkwerks Ultralight Research and Development Facility —shortened to Skonkwerks — represents a team from Larsen, Wisconsin. Skonkwerks honored Alberto by first building a 23 Bis and later the 24 Bis. The group describes itself as a “loosely knit organization of friends, flyers, and fanatics… tinkerers, builders, and bullsh###rs. We are engineers, designers, and dreamers hanging out in a little hangar screwing stuff together and making it fly.”
Lee Fischer was the founder of this group of tinkerers that formed after he first showed a highly modified Robertson B1-RD. So much interest was shown in the Demoiselle style of aircraft that he decided to build a 23 Bis. At AirVenture 2015, his friend Mark Solper hinted that it would be “great project to build a pair of ‘evolved’ Demoiselles for a subsequent AirVenture.” This suggestion led to the 24 Bis.
Mark, Lee, and the whole merry band machined and welded the airframe and sewed Dacron wings, all the while learning both new skills and an appreciation for what Santos Dumont and his associates had done more than a hundred years earlier.
The aircraft was flown into Oshkosh.
Weight — 240 pounds
Wing Span — 32 feet
Wing Area — 192 square feet
Never Exceed Speed — 45-50 mph
Stall Speed — 14-16
Engine — Rotax 447
Build Time — December 21, 2014 through June 21, 2015
Skonkworks 23bis
The Winchester Skonkwerks Ultralight Research and Development Facility — let’s shorten that to Skonkwerks — represents a team from Larsen, Wisconsin. Skonkwerks honored Alberto Santos Dumont by first building a 23 Bis and later the 24 Bis. The group describes itself as a “loosely knit organization of friends, flyers, and fanatics… tinkerers, builders, and bullsh###rs. We are engineers, designers, and dreamers hanging out in a little hangar screwing stuff together and making it fly.”
Lee Fischer was the founder of this group of tinkerers that formed after he first showed a highly modified Robertson B1-RD. So much interest was shown in the Demoiselle style of aircraft that he decided to build a 23 Bis. At AirVenture 2015, his friend Mark Solper hinted that it would be “great project to build a pair of ‘evolved’ Demoiselles for a subsequent AirVenture.” This suggestion led to the 24 Bis
Weight: 240#
Wing Span: 32′
Length: 19′
Wing Area @ Chord: 176 sq. ft.
Wing Area @ Camber: 192 sq. ft.
Wing Construction: Tube and Sewn Dacron
Skoglund 1910 Monoplane
Present but not flown at the Los Angeles Aviation Meet at Dominguez in January 1910. This engine-less plane had unique “ailerons”, being like roller blinds controlled by a lever such that one increases in area as the other decreases. Charles Skoglund was active in the Aero Club of California.
Skoda-Kauba SK V8
Other designs in the series included the V8 primary trainer, none of which entered production.
