Kahnt was taught to fly by Hans Grade and opened the “1. Sächsische Fliegerschule” in Leipzig.
With his “Falke”, Kahnt flew over the “Völkerschlachtdenkmal.”
As head pilot at the Gothaer Waggonfabrik during the war, he was killed in a crash.
Kahnt was taught to fly by Hans Grade and opened the “1. Sächsische Fliegerschule” in Leipzig.
With his “Falke”, Kahnt flew over the “Völkerschlachtdenkmal.”
As head pilot at the Gothaer Waggonfabrik during the war, he was killed in a crash.

Conrad Kadlec and his partners August Helpertz and Gustav Schlößer of Düsseldorf-Holthausen were granted a patent for this “Flugmaschine mit Wendeflügelrädern” in 1910. Little more is known of the unlikely-looking machine with rotating and twisting wings on a transverse horizontal axle.

The Canard was a design of Pierre Juvigny which was in the list of about 56 enlisted competitors of the Concours de sécurité 1914 which was published on 17 January 1914. The Concours started in June 1914, but the Juvigny Canard was not ready for competition.

It is noted that the jury nevertheless inspected the incomplete machine (unable to compete) and inspected the variable incidence mechanism of the wing. Due to the weight of the engine and ancillary equipment the machine stood with the nose high when on the ground. There is no information that it took to the air and after the outbreak of the war in begin August 1914 experiments were presumably halted.


Light sailplane circa 1998. The Skua can be split into three parts for transport on a roof rack or trailer. It came equipped with a BRS.
Weight: 70 kg
Wing span: 12.6 m
Wing area: 12.2 sq.m
Vne: 110 km
Stall: 32km
Glide Ratio: 25
Price (1998) US$15000
1998: Estrada da gavea 655, Apt: 1603 sao Conrado, CEP 22 100000 Rio de Janeiro, BRAZIL
Glider builder

Troy Woodland designed the Just 103 to conform to the FAA Part 103 requirements for ultralight aircraft, including a maximum weight of 254 pounds, a single seat, and a top speed of 63 mph. The new ultralight logged 1.5 hours before heading to the Sun ‘n Fun International Fly-In and Expo. Other than a narrow windscreen, the pilot is very much out in the open air, “which was typical with a lot of earlier Part 103 designs”.
A Polini Thor 250 engine from Italy supplies 37 horsepower at 7,500 rpm, and retails for less than $4,000. Woodland also expected to mount a Rotax 582, which would push the aircraft beyond the ultralight limits and require registration as a light sport or experimental light sport aircraft.
The company was to sell the Just 103 as a kit or ready-to-fly from the factory in Walhalla, South Carolina.

The Just Aircraft SuperSTOL is a classic doped fabric/chrome moly steel frame taildragger with automatically deploying full-span two-segment leading-edge slats, 15-25-40-degree barn door flaps, Rotax 912 power and hydraulic shock-absorbing main gear struts.
The SuperSTOL is based on the Just Highlander. The base price (kit) for the SuperSTOL in 2012 was $36,650 (before engine and avionics), with S-LSA certification underway.

Introduced at Arlington and Oshkosh 2004, Highlander is an upgraded version of the Escapade. Just Aircraft’s new bush plane qualifications are enhanced by a larger balanced elevator and rudder, a larger trim tab, extended (and beefed up) gear legs with larger wheels and brakes, gull wing doors (can be opened in flight), an 8″ tail wheel and VG’s. And, a new three foot longer wing.
The Highlander has the same features as the Escapade, but with all the upgrades to make it a better backcountry aircraft. The Highlander is manufactured with all high quality aircraft materials. It is also manufactured with attach points for floats, lots of cabin area and extra large cargo area.
The Escapade and Highlander share considerable structural elements including the chrome-moly fuselage frame, wing airfoil construction, and engine compartment.
Using the same basic fuselage for both planes means they both have a huge luggage capacity that extends to the tail. The planes can handle a 6’7”+ frame and 300lb+ people. With sliding seats and 44” of elbow room.
Highlander LSA 2010 Kit Price: US$22,250
Both planes can be flown with the doors off or the doors and windows open, although a heater can be installed for frigid conditions.
The planes are available as complete ready to assemble kits which take about 600 – 700 hours to complete. Or you may choose various stages of assembly based upon your time demands and pocket book. Some choose to have the factory finish the wings and cover the fuselage which cuts the build time in half. There is also the option of “Build Assist” where for a monthly fee the owner may assemble the plane in the factory with company experts on hand for assistance. Those desiring a complete build ready to fly option will find this also available.
This would be SLSA certified if desired.
An extended-gear option for the Highlander provides heavy-duty axles to support bush tires: those legs raise the fuselage and widen the track by about 4 inches.
The Highlander is the bush plane model of the Escapade with longer wings, taller-heavier gear, tundra tires and larger tail feathers with balanced elevator and rudder.

The Escapade and Highlander can be installed with any power plants in the weight range of the Rotax 503 up to the Rotax 914 or Jabiru 2200 up to the Jabiru 3300.
Engine: Rotax 912 100 hp
Height: 7’10”
Length: 19′
Cabin Width: 44 in
Wing Span: 31′ 6″
Wing Area: 120.75 sq.ft
Empty Weight: 620 lbs
Gross Weight: 1320
Useable Load: 700
Fuel Capacity: 18 USgal
Flight Load Factor: +4 -2 G
Vne (never exceed speed): 130 mph
Cruise speed @ 75% power: 105 mph
Vso (full flap) at Gross Weight: 23 mph
Vs (clean) at Gross Weight: 27 mph
Take off Distance Ground Roll: 300 ft
Landing Distance Ground Roll: 250 ft
Highlander LSA
Engine: Rotax 912S, 100 hp
Wingspan: 31′ 6″
Length: 19 ft
Wing area: 116.25 sq.ft
Empty weight: 620 lb
MTOW: 1320 lb
Useful load: 700 lbs
Cruise 75%: 105 mph
Stall: 25 mph
Range: 520 sm
ROC: 1500 fpm
Takeoff dist: 100 ft
Landing distance; 75 ft
Seats: 2
Cockpit width: 44 in
Engine: Rotax 912S, 100 hp
Wing Span: 31’6”
Wing area: 120.75 sq.ft.
Mean Cord: 45”
Length: 19’
Height: 7’10”
Length Folded: 20’8”
Width Folded: 7’ 11.5”
Number of Seats: 2
Number of Doors: 2
Landing Gear: 8” Tail Wheel
Gear Width: 76”
Fuel Capacity: 18 or 26 USGallons (24 useable)
VNE: 130 mph
Cruise: 110 mph
Stall With Flaps 40 deg: 27 mph
Stall Clean: 32 mph
Take off Roll: 300 ft
Take off Distance to 50 ft: 800 ft
Ground Roll: 300 ft
Landing Distance from 50 ft: 1000 ft
Climb Rate: 880 fpm
Gross weight: 1320 Lbs
Empty weight: 615 Lbs
Useful Load: 705 Lbs
Load Limit Factors: +4 g’s –2 g’s

The Escapade has been developed to meet the demand for a two place side-by-side dual control (individual stick controls) aircraft that can be used for training as well as recreation.
The Fuselage, tail and landing gear are manufactured from 4130 Chrome-moly steel.
The original Escapade earned the United Kingdom’s BCAR (British Civil Aviation Requirement) Section S structural – and flight – test standards.
The wings fold in under 2 minutes with no disconnecting of any controls or control surfaces. The Escapade can be configured with tail-wheel or tri-cycle landing gear with the ability to swap from one to the other in about 1 hour.
The Escapade has been through UK Section S static testing certification requirements and flight-testing certification requirements. The Escapade can be installed with any power plants in the weight range of the Jabiru 2200 or Rotax 912/914. Jabiru Pacific can provide from the firewall forward.
The Escapade and Highlander share considerable structural elements including the chrome-moly fuselage frame, wing airfoil construction, and engine compartment.
Using the same basic fuselage for both planes means they both have a huge luggage capacity that extends to the tail. The planes can handle a 6’7”+ frame and 300lb+ people. With sliding seats and 44” of elbow room.
Both planes can be flown with the doors off or the doors and windows open, although a heater can be installed for frigid conditions.
The planes are available as complete ready to assemble kits which take about 600 – 700 hours to complete. Or you may choose various stages of assembly based upon your time demands and pocket book. Some choose to have the factory finish the wings and cover the fuselage which cuts the build time in half. There is also the option of “Build Assist” where for a monthly fee the owner may assemble the plane in the factory with company experts on hand for assistance. Those desiring a complete build ready to fly option will find this also available.
This would be SLSA certified if desired.
Escapade LSA 2010 Kit Price: US$20,250
The Escapade and Highlander can be installed with any power plants in the weight range of the Rotax 503 up to the Rotax 914 or Jabiru 2200 up to the Jabiru 3300.
Variation:
Lanitz Escapade Two
Engine: Rotax 912, 80 hp
Height: 7’2”
Length: 19′
Cabin Width: 44 in
Wing Span: 28′ 6″
Wing Area: 108 sq.ft
Empty Weight: 615 lbs
Gross Weight: 1320
Useable Load: 705
Flight Load Factor: +4 -2 G
Vne (never exceed speed): 130 mph
Cruise speed @ 75% power: 110 mph
Vso (full flap) at Gross Weight: 27 mph
Vs (clean) at Gross Weight: 32 mph
Climb Rate (sea level @ gross): 880 ft/min
Take off Distance Ground Roll: 300 ft
Landing Distance Ground Roll: 300 ft
Fuel Capacity: 18 USgal
Escapade LSA
Engine: Jabiru 2200 85 hp
Wingspan: 28′ 6″
Empty weight: 620 lb
MTOW: 1320 lb
Useful load: 700 lb
Cruise 75%: 110 mph
2010 Kit Price: US$20,250
Engine: Rotax 912S, 100 hp
Wing Span: 28’6”
Wingarea: 108 sq.ft.
Mean Cord: 45”
Length: 19’
Height: 7’2”
Length Folded: 19’2”
Width Folded: 7’ 11.5”
Number of Seats: 2
Number of Doors: 2
Landing Gear: Tricycle or Tail Wheel
Gear Width: 72”
Fuel Capacity: 18 or 26 USGallons (24 useable)
VNE: 130 mph
Cruise: 110 mph
Stall With Flaps 40 deg: 27 mph
Stall Clean: 32 mph
Take off Roll: 300 ft
Take off Distance to 50 ft: 800 ft
Ground Roll: 300 ft
Landing Distance from 50 ft: 1000 ft
Climb Rate: 880 fpm
Gross weight: 1320 lbs
Empty weight: 615 lbs
Useful Load: 705 lbs
Load Limit Factors: +4 g’s –2 g’s
Caldwell, Idaho, USA.
Just Aircraft was founded in 2002 when aircraft designer Troy Woodland left his position at Flying K Enterprises, manufacturer of the Sky Raider kit. Troy wanted to design a plane of his own. He met Gary Schmitt at an air show and Gary wanted a plane with many of the features of the new Escapade.With Gary’s backing they collaberated on a design.
The Escapade has a huge luggage compartment, a more roomy cabin , and a simplified wing-folding mechanism that avoids the need to remove control linkages.
Soon after the Escapade came the Highlander, a more rugged plane that was the bush airplane they wanted. The Highlander Debuted at Arlington in 2004, and by 2010 dominated Just’s sales by three-to-one aircraft sold .
In 2004 the company relocated to Walhalla, South Carolina, into a state of the art production facility with its own runway. This was a time of serious growth for Just Aircraft, when materials buying and costs analysis became implemented, when marketing, accounting, and all other true “front office” needs of the growing company were founded.
Over 170 kits had been shipped worldwide: including England, France, Spain, New Zealand, Canada and Equador. Sales are running about 50/50 domestic and export.
In addition to selling kits, Just Aircraft offers customers a build assist program, where they can construct their plane in the factory, or the Company will build 100% of the plane in accordance to the customers specifications.