Kirkham, Chas. B

Chas. B Kirkham (1882-1969) was a friend and collaborator of Glenn Curtiss. He made motorcycle engines from about 1900, and in 1910 an aero engine. In 1915 he joined Curtiss in engine work and is chiefly known in connection with the famous D-12. Wanting a fighter worthy of his K-12 engine, with its small frontal area, Kirkham planned a two-seat triplane with excellent streamlining, first flown July 5,1918. To this record-breaker the name Kirkham Fighter, 18-T or Curtiss-Kirkham was applied, though the Curtiss name alone was later used for land and sea versions. U.S. Army had 18-B biplane equivalent, also sometimes called Curtiss-Kirkham. Navy’s two 18-Ts were later adapted for racing. In 1920s Kirkham’s company Kirkham Products designed aircraft to special order.

Kinner Kin Air

W.B.Kinner, son of the Kinner Fleet designer and a Captain with Saturn Airways, completed a fifteen year homebuilt project designed so it could be built in his garage.

The wings are metal and plywood, and the fuselage is plywood with fibreglass cowl and turtledeck.

Kin Air
Engine: Lycoming O-290-G4, 125 hp
Wingspan: 16 ft 6 in
Length: 14 ft 6 in
Height: 5 ft
Empty weight: 705 lb

Kinner R-715

The R-715 can be installed as tractor or pusher. The standard starter mount affords a wide range of starters, as Heywood injection, hand turning gear, electric or combination starters, electric starters etc. The provision of a standard drive for an electric starter affords use of electric type starters, lighting system, radio etc. Provision of a fuel pump drive allows various locations of fuel tanks. The carburettor location allows gravity feed. Standard SAE propeller end of crankshaft provides for use of a minimum weight metal propeller hub.

Type: 5 cylinder 4 stroke air cooled radial
Manufacturer’s Rating: 190 hp at 1800 rpm
Displacement: 715 cu.in
Compression ratio:
Bore: 5 5/8 in
Stroke: 5 3/4 in
Length: 34 13/16 in
Diameter: 50 in
Weight: 410 lb
Lubrication: Circulating oil system, pressure feed to front & rear main bearings, and to plain link pins, through grooved master rod bearings.
Ignition: 2 Scintilla magnetos
Carburation: Stromberg

Kinner R-5 / R-53 / R-55 / R-56 / R-540

Kinner R-56 installed in a PT-22 Recruit

The Kinner R-5 is an American five cylinder radial engine for light general and sport aircraft of the 1930s. The R-5 was a development of the earlier Kinner B-5, with slightly greater power and dimensions. The main change was the increase in cylinder bore from 117 mm (4.625 in) to 127 mm (5 in) and an increase in cylinder stroke from 133.3 mm (5.25 in) to 139.7 mm (5.5 in). This led to a corresponding increase in displacement from 7.2 liters (441 cu in) to 8.8 liters (540 cu in).

The head of the R-5 Series 2 has approximately three times as much cooling fin area as previously used cylinder heads, having longer fins spaced closer together. A greater angle between inlet and exhaust valves results in a stronger head and provides additional metal between valve seats. Cylinder heads have rear exhaust ports and lugs are provided for support of cowling rings.

Enlarged intake passages and valves increase the efficiency and result in higher brake mean effective pressure.
Bearings have been increased in size. The crankshaft has been greatly strengthened by increased sections. The main and master rod bearings are of the copper lead steel-backed type. Master-rod sections have been enlarged and design altered to give a very much stronger rod with little increase in weight. Improved front cover provides additional strength and durability. All oil passages are contained in the engine.

Kinner R-5 Series 2

Rocker arms have a roller supported on needle bearings on valve end which reduces side thrust on valve and increases life of valve guides. High pressure grease lubrication is provided for the main roller bearing of the rocker arm and the rocker arm end of pushrods. Pushrod rocker arm adjusting screws are designed so that with their removal the pushrod can be withdrawn through the opening of the rocker arm for inspection.

The Kinner R-5 Series 2 employs a separate camshaft for each of the five cylinders. Each camshaft includes a simple spur gear driven by pinion gear on rear end of crankshaft at one-half engine speed.

Spur type magneto drive gears are driven by the cam gears. Oil pressure and scavenger pumps are driven by shafts keyed into slots in the ends numbers three and four camshafts, respectively.

Provision for Eclipse compressed air started and Eclipse Y150 direct electric starter, also generator and fuel pump drives are provided. Each accessory has its own mounting pad. Provision is made in oil sump for Cuno oil filter.

This engne may be fitted with battery ignition and two machine gun synchronising drives were available.
The R-5 was a rough running but reliable engine and the R-5 and its derivatives were produced in the 1,000s, powering many World War II trainer aircraft, its military designation R-540.

Kinner R-5 160hp

Applications:
Kinner Sportwing
Kinner Playboy
Meyers OTW
N2T Tutor
Ryan PT-22 Recruit

Variants:
R-5
R-53
R-55
R-56

Specifications:
Kinner R-5
Type: 5-cylinder air cooled radial
Bore: 5 in (127 mm)
Stroke: 5 1⁄2in (139.7 mm)
Displacement: 540cu in (8.85 L)
Length: 32.3in (820.4 mm)
Height: 45.6in (1,157 mm)
Dry weight: 330lb (149.6 kg)
Valvetrain: 1 inlet and 1 exhaust valve per cylinder
Fuel system: 1 Stromberg carburetor
Fuel type: 73 octane
Oil system: Dry sump
Cooling system: Air
Power output: 160hp at 1,850 RPM max/113hp at 1,800 RPM cruise
Compression ratio: 5.50:1
Power-to-weight ratio: 0.48 hp/lb

Kinner R-5 Series 2
Cylinders: 5 radial
Bore: 5 in
Stroke: 5.5 in
Displacement: 540 cu.in
Power: 160 hp at 1850 rpm
Weight: 325 lb
Compression: 5.5-1
Ignition: 2 x Scintilla Magneto
Carburettor: Stromberg NA-R6
Crankshaft Prop end: No.1 SAE Standard