A prototype in the VTOL arena was the 33,000 lb Hiller X-18 tilt-wing convertiplane. The X-18 took to the air for the first time in November 1959, and in overall concept was configured as a transport type. Power was provided by two 5850-shp (4362-kW) Allison T40-A-14 turboshafts driving the two contra-rotating propeller/rotor units located one on each wing, and a 3400-lb (1542-kg) thrust J34 turbojet providing exhaust gases to a tail-mounted thrust diverter used for longitudinal control in vertical flight.
Stanley Hiller Jr designed the Model 360 which has enjoyed considerable commercial success since its first flight in 1948. It was derived from the UH-5 which had proved very unstable during trials and had subsequently been fitted with a new stability system patented as the Hiller ‘Rotormatic’. It entailed fitting the two-blade rotor with two small paddles which acted as a control rotor and were also connected to a hanging stick. This servo ‘paddle control’ system tilts the rotor head and actuates the cyclic pitch control. The Hiller 360 received its FAA (Federal Aviation Administration) approval in October 1948 and a year later a production model designated Model 12 made the first transcontinental helicopter flight across the USA. At that time it still had an open cockpit, and the 178hp Franklin 6V4-178-B33 was in an open engine bay.
Known as the Hiller UH-12 as Hiller had become part of United Helicopters, the Hiller UH-12, incorporating a two-bladed main rotor and a two-bladed tail rotor on an upswept boom. The UH-12 had a framed ‘bubble’-type cabin, no fuselage structure around the engine, skid undercarriage and a 175hp Franklin 6V4-178-B33 engine. Maximum takeoff weight was 1015kg.
The UH-12A Raven production two-seat UH-12 with collective pitch ballast system and wooden rotor blades for civil and military customers had a takeoff gross weight of 1082kg. With an uprated engine and new UH-12A rotor blades, it was purchased by the US Army and Navy for battlefield evacuation and observation tasks, with the designation H-23 Raven, whilst the Navy ordered the same basic model as the HTE-1 for training.
The commercial UH-12A to UH-12D became the OH-23A to OH-23D Raven respectively for service with the US Army, and the US Navy acquired UH-12As as HTE-1 and HTE-2.
HTE-2
The UH-12A successor, the H-23B, powered by a 200-210hp Franklin engine, was the first version used by the US Army as a trainer. 216 were assigned to the Primary Flying School at Fort Walters and another 237 were used for various tasks. The Hiller UH-12 was the US Army’s primary trainer until 1965. The UH-12B (and as the HT Mk.1 for the Royal Navy) normally had skid or flotation gear, but a wheeled undercarriage was fitted to a batch ordered by the US Navy (the HTE-2).
In 1955 the UH-12C, was basically a UH-1B. It retained the 200hp Franklin engine, but had all-metal rotor blades and a “goldfish bowl” cockpit canopy and three seats. From 1956, 145 were delivered to the US Army as the H-23C.
UH-12C
A purely military version, the UH-12D / OH-12D, flew on 3 April 1956 and 483 went to the US Army. The Franklin engine had been replaced by the more powerful 320hp Lycoming VO-540, and the transmission had also been changed to increase the service life of the helicopter.
The commonest version was the UH-12E which had a more powerful 305hp Textron Lycoming VO-540-A1A engine. The US Army replaced nearly all the OH-23Ds by Hiller 12Es, designated OH-23G 3-seat dual control trainer. In 1960 the Model E4 was developed from the Hiller 12E, with a longer cabin to seat four and an anhedral stabilizer on the tail boom. Twenty-two of these were acquired by the US Army as the OH-23F, for geodetic research.
Hiller UH-12E ZK-HFG
In 1963 the US Army was buying 137 more Hiller OH-23 observation helicopters to meet its requirements until a five-way competition for a light helicopter was decided at Ft. Rucker, Alabama. In 1963 the British navy was adding seven UH-12E to the 14 bought in 1962. The Royal Navy used its 12E’s to train fleet pilots at Culdrose Naval Air Station in Cornwall. They were fitted for instrument flying. 12E were also in use with Canada’s army and air force, known as CH-112.
The UH-12EL was a UH-12E retro-fitted with Ham-Standard rotor stability augmentation system, stainless steel rotor blades and 1400kg TOGW. UH-12E3 was the revised designation for Hiller Aircraft Corp production UH-12E with 3 seats, and UH-12E3T the Hiller Aircraft Corp UH-12ET. The UH-12E4 featured inverted rear tail planes and lengthened cabin to accommodate pilot plus rear bench seat for 3 pax. All new helicopters now have these features and they can be retrofitted on Model 12Es. Designated UH-12E4T when fitted with Soloy conversion to 400shp Allison 250-C20B turboshaft. This engine conversion was jointly developed with Soloy Conversions of Chehalis, Washington who began work on it in 1976.
The UH-12ET was the UH-12E fitted with Soloy conversion to 400shp Allison 250-C20B turboshaft. UH-12E5 was the UH-12E4 fitted with five seats and 340hp Textron Lycoming VO-540 piston engine. A prototype was flown but no further development was undertaken. The Korean War gave an added impetus to improvements and when the Hiller 12E appeared in 1959 it came either as the L3 with a 305hp Lycoming VO-540-C2A or as the SL3 with a supercharged 315hp TIVO-540-A2A engine. The UH-12SL was the UH-12E with supercharged Textron Lycoming TIVO-540 engine and ‘L’ series rotor head with gyro-controlled stability augmentation system. UH-12L was UH-12SL with unsupercharged VO-540 engine.
Civil versions with uprated powerplant included the UH-12E variants suffixed L3, L4, SL3 and SL4. The last civil variant, which appeared in 1963, was the Hiller 12L4 which was also used as a test-bed for a PT6 turbine, but the project was taken no further. Total sales of the Hiller 12E family exceeded 2000. Over 1,600 UH-12s went to the US Army and were used in Korea and Vietnam. At the height of UH-12/OH-23 production Hiller was taken over by the Fairchild Corporation, but in 1973 a new company, Hiller Aviation, acquired design rights and production tooling for the UH-12E, and for some years provided support for the world-wide fleet of UH-12 variants. UH-12E5T was a proposed turbine-powered UH-12E5 with Allison 250-C20B. Not built. UH-12J-3 was an unofficial designation for Soloy-converted UH-12E. UH-12SL4 was the UH-12L with the E4 four-seat cabin.
The Canadian army acquired OH-23Gs which it operated with the designation CH-112 Nomad, and the Royal Navy used a number of ex-US Navy HTE-2s under the designation Hiller HT.Mk 2. In April 1984 Hiller became a subsidiary of Rogerson Aircraft of Port Angeles, Washington. Renamed Hiller Helicopters and later Rogerson Helicopters, the company, now known as Rogerson Hiller, relaunched the piston-engined UH-12E in 1991 as the Hauler, and a number have been exported. The company is also proposing the Allison turbine-powered UH-12ET development for the US Army’s NHT (New Training Helicopter) requirement. The Model 12 has the usual equipment for helicopter safety and civil work, but can also be fitted with a night-lighting kit, a 454kg capacity cargo hook, twin heavy duty cargo racks, and auxiliary fuel tanks. Equipped with extra tanks the 12E has a maximum range of 676km. Production of both the 12E and 12E-4 is ran at about five a month.
A number were fitted with an Allison 250-C20 turbine as Soloy UH12E-SCL conversions. The 400shp Allison (derated to 305 shp) is mounted slanting backwards from the adaptor gearbox, leaving a large uncluttered area where the previous engine was.
UH-12E / OH-23G Engine: 305hp Textron Lycoming VO-540-A1A / Lycoming VO-540-C2A, 305 hp. TBO: 1200 hrs. Main rotor: 10.8 m / 35.3 ft. Seats: 3. Length: 40.7 ft. Height: 10.1 ft. Max ramp weight: 3100 lbs. Max takeoff weight: 3100 lb / 1410 kg. Standard empty weight: 1759 lbs. Max useful load: 610 kg / 1341 lbs. Max landing weight: 3100 lbs. Max sling load: 1000 lbs. Disc loading: 3.2 lbs/sq.ft. Power loading: 10.2 lbs/hp. Max usable fuel: 516 lbs. Max rate of climb: 993 fpm. Service ceiling: 15,000 ft. Hover in ground effect: 10,400 ft. Hover out of ground effect: 6800 ft. Max speed: 83 kts. Normal cruise @ 3000 ft: 51 kts. Max cruise: 80 kts Fuel flow @ normal cruise: 125 pph. Endurance @ normal cruise: 3.9 hr. Max range: 390 km. Seats: 3.
UH-12EL Engine: 305hp Textron Lycoming VO-540-A1A TOGW: 1400 kg
UH-12E-L3 Engine: Lycoming VO-540-C2B, 305 hp Main rotor diameter: 35 ft 5 in / 10.80 m Empty weight: 1759 lb / 798 kg Normal TO weight: 2800 lb / 1270 kg Max overload weight: 3100 lb / 1405 kg Max cruise SL: 78 kt / 90 mph / 145 kph Max ROC SL: 1290 fpm / 393 m/min Service ceiling: 15,200 ft / 4630 m Range w/aux fuel, 2800lb/1270kg: 379 nm / 437 mi / 703 km Seats: 3 Baggage capacity: 125 lb / 57 kg Cabin length: 5 ft 0 in / 1.52 m Cabin width: 4 ft 11 in / 1.50 m Cabin height: 4 ft 5 in / 1.35 m
Stanley Hiller Jr designed the two-seat Model 360 which first flew in 1948. It was derived from the UH-5 which had proved very unstable during trials and had subsequently been fitted with a new stability system patented as the Hiller ‘Rotormatic’. It entailed fitting the two-blade rotor with two small paddles which acted as a control rotor and were also connected to a hanging stick. This servo ‘paddle control’ system tilts the rotor head and actuates the cyclic pitch control.
Of all-metal construction with fixed tricycle undercarriage. Equipped with a fully enclosed cabin and rear fuselage, an overhead mounted control stick is attached to a Hiller rotor control. Power is by one 175hp Franklin 6V4-178-B32 engine. The prototype was registered N68940.
It received its FAA (Federal Aviation Administration) approval in October 1948 and a year later a production model designated Model 12 made the first transcontinental helicopter flight across the USA in the summer of 1949. At that time it still had an open cockpit, and the 178hp Franklin 6V4-178-B33 was in an open engine bay.
Hiller 360
In 1949 a Hiller 360 demonstrated a pilot-less cross-country flight with two observers well away from the pilot’s seat. The 25 mile flight over San Francisco Bay was at 3800 ft after a normal piloted take off.
Pilotless Hiller 360
Hiller 360 Engine: Franklin 6V4-200-C33, 200 h.p. Rotor diameter: 35 ft. Rotors: 2-blade main; 2-blade tail Fuselage length: 27 ft. 6 in. Loaded weight: 2,500 lb. Max. speed: 84 m.p.h. Ceiling: 9,400 ft. Typical range: 135 miles at 70 mph Seats: 3.
HTE-1 Engine: Franklin 178 hp Undercarriage: 3-wheel
The UH-5 had proved very unstable during trials and had subsequently been fitted with a new stability system patented as the Hiller ‘Rotormatic’. It entailed fitting the two-blade rotor with two small paddles which acted as a control rotor and were also connected to a hanging stick. This servo ‘paddle control’ system tilts the rotor head and actuates the cyclic pitch control.
The UH-4 was a development of the XH-44, which retained the co-axial contra-rotating two-bladed rotors, though the diameter was considerably increased. A two-seat all-metal helicopter with tricycle undercarriage, three were built. The prototype was registered N67706.
The FH1100 originated from Hiller Aircraft Company’s entry for the US Army requirement of a Light Observation Helicopter (LOH). Designated OH-5A for the technical “fly-off’ it competed against Bell’s OH-4A (B206) and Hughes OH-6A (H369).
Fairchild Stratos Corporation acquired Hiller in 1964 believing they were about to secure a large military contract as the OH-5A stood out the preferred winner. Leaked production data of the OH-5A resulted in Howard Hughes successfully under bidding with the OH-6A. The first FH1100, N81005, flew on 21 January 1963, powered by the Allison T63 turbine engine. Fairchild meanwhile announced they would begin civilian helicopter production of a refined OH-5A, designated the FH1100, offered for sale in June 1966 with either 4 or 5 seats. It became the first US civil turbine helicopter to go into production with a modest 246 units completed by 1971. A small number were produced between 1983 and 1985. This utility helicopter has a semi-monocoque fuselage and conventional tail boom. The semi-rigid two-blade main rotor, able to be stored folded, is controlled by dual hydraulics, with the primary assisting cyclic and collective, the secondary pump actuating the cyclic only. A prototype was constructed by Helicopter Technology Inc. in Century, Florida, in 2002 for the new FH1100 to go back into production as the FHoenix.
RH1100
Under development in 1991 by Rogerson Hiller, the RH1100S features a lengthened and widened cabin and a LCD instrument display.
Stanley Hiller flew the first successful American co-axial helicopter, the XH-44, in July 1944, when he was only 19 years old. It also featured the world’s first successful all-metal rigid-rotor blades. Hiller had learned to fly from his father at an early age, and at 16, Hiller had started a business building small gasoline engine model cars; revenue eventually grew to $100,000. Hiller became interested in helicopters in 1937 when he saw pictures of the Focke Wulf Fw 61 and Sikorsky’s VS-300 in 1939. Hiller felt the tail rotors used on the VS-300 and the outriggers on the Fw 61 were wasteful and possibly unnecessary. The XH-44 evaluated three different rotor configurations: rigid, articulated, and semi-rigid, which was selected. The engine was uprated from a 90hp Franklin to a 125hp Lycoming. The XH-44 was the first successful helicopter west of New York, and Hiller made public demonstrations of the XH-44 in nearby San Francisco.
The first of the Army’s designated VTOL research aircraft was a continuation of the work to develop a ‘flying platform’. The idea for a machine of this kind, making use of kinesthetic control (in which the pilot leans in the direction he wishes to go) is attributed to Charles H. Zimmerman and dates back to 1940.
In the early 1950s, N.A.C.A. (the forerunner of N.A.S.A.) undertook a research programme at Langley Laboratory to prove the idea. Three types of aircraft were studied, each capable of carrying one man who stood on a platform, and supported, respectively, by a rotor, a ducted fan and compressed air. Subsequently, the Army placed contracts for further development of a rotor type flying platform by de Lackner (the Aerocycle) and of the ducted fan type by Hiller. The Hiller Helicopter Company had by this time already completed some studies in conjunction with Charles Zimmerman, in 1947, but no free flights were then achieved. A contract was placed with the company in 1953 for the construction of a prototype under Office of Naval Research supervision and this flying platform achieved its first successful untethered flight in February 1955.
The Pawnee featured a pair of contra-rotating rotors spinning inside a duct with a diameter of 1.5 meters (5 feet). Each rotor was driven by its own 30 kW (40 HP) two-stroke engine. The pilot stood above the duct, surrounded by a circular handrail and protected by a safety harness. He controlled the engines with a twist-grip throttle and leaned to guide the aircraft. The duct improved safety during takeoff and landing. The duct also provided additional lift, since there was a horizontal “lip” around its top edge that curved down into the duct. The airflow into the duct resulted in low air pressure above the lip, and the pressure difference between the top and bottom of the lip generated a net upward force, providing as much as 40% of the total lift of the aircraft.
In practice, speeds of up to 15 m.p.h. were achieved. Hand controls included the throttles to control vertical movement and a control to apply power deferentially to the two propellers in order to keep the platform headed in the right direction.
The Pawnee handled very well in flight tests. The machine was then modified with longer landing gear legs to increase ground clearance, and eight vanes were mounted underneath the duct to improve flight control.
Results of the trials with their early platform were sufficiently promising for the Army to award Hiller a second contract, in 1956, for two larger examples of the flying platform. These were designated W‑ I E (serials 56‑6944 and 56‑6945).
VZ-1E
In the W 1E, the diameter of the duct was increased to 8 ft. and the chord was more than doubled. Three interconnected 30 kW (40 HP) Nelson H 56 engines supplied power to the counter rotating propellers. Controls were modified to be similar to those in a helicopter and the pilot had a rudimentary seat.
First flight of the W 1E (56 6944) was made on February 4th, 1955. It was delivered to the Army in 1959 but no further development occurred.
On January 10, 1957, the US Navy announced the successful first flight of the one man collapsible Rotorcycle, developed for the US Marine Corps by Hiller Helicopters of Palo Alto, California. Hiller was one of two companies selected during 1954 to design and build a one man helicopter but the idea was not wholly successful and it failed to achieve full production status after initial flight testing was completed by July 1957. Designated XROE 1, this was a unique one-man helicopter which could fold into a small package for easy transportation or parachute delivery. Weighing less than 250 lbs it was powered by a Nelson four cylinder opposed, two cycle, air cooled petrol engine manufactured by Barmotive Products Inc a single rotor, eighteen feet in diameter and positioned above the pilot’s head, provided lift, with a small tail rotor located in a tubular boom compensating for torque. The entire helicopter was held together by quick release pins and could be assembled by one person. Although not literally a ‘strap on the back’ machine, the XROE 1 approximated closely to this idea, since the pilot sat on what appeared to be a bicycle seat, with the engine just behind him. The US Marine Corps intended to use the XROE 1 for observation, liaison, small tactical missions, such as escape and evasion, pilot rescue and any other James Bond’ type drama.
Transmission of the Rotorcycle incorporated a single spiral bevel gear set and an over-running clutch while the fuel system was of the gravity feed type. Official Marine Corps specification data indicated that the XROE 1 could be folded or assembled in the field in less than five minutes and, for aerial drops to downed pilots or stranded troops, the folded Rotorcycle fitted into a streamlined container suitable for external transportation on a fixed-wing aircraft. It was expected to enter service by Septembr 1959.
During May 1958, while on a European sales tour, the Hiller XROE 1 Rotorcycle was demonstrated at Elstree aerodrome, Herts. On this occasion, two men assembled the machine in just three minutes, a rather slow time according to the manufacturers who stated that the record stood at one minute fifty seconds. Although based around a Marine Corps specification, the XROE 1 was evaluated by both Germany and Switzerland, the licensee in Europe being Helicop Air of Paris and the estimated cost was $10,000 for production machines.
Demonstration in England 1955
In November 1958, a contract was signed for a batch of ten Rotorcycles to be built by Saunders Roe at its Eastleigh, Southampton factory, on the basis that it would cost less to build a small batch of XROE 1s in the United Kingdom than in the USA. Helicop Air of Paris, Hiller’s agent in Europe, was responsible for handling the contract which was quite unique.
Using materials from the USA, Saunders Roe built the jigs and tools, manufactured the gearing, transmission components and the structure. All proprietary items, including the engine, electrics, main rotor blades and instruments, were also supplied from the USA. The Rotorcycles were completed in accordance with Hiller drawings.
Saro-built Rotorcycle
The control technique was known as the Hiller Rotormatic system while, in place of a landing gear, the Rotorcycle was supported on three tapered aluminium alloy spring tubes.
The fate of the majority of the XROE 1 Rotorcycles after leaving the Eastleigh factory of Saunders Roe is not known, but the type was evaluated for the Marine Corps at the Naval Air Test Centre and the published performance figures are based on this evaluation. Three Rotorcycles all designated YROE 1 were also assessed by NASA at their Ames facility at Moffett Field, California, YROE 1s ‘4020’ ‘4021’ and ‘4024’ being delivered there on November 16, 1962. The serial numbers applied to the YROE 1s tonsisted of four digits only, this system not conforming to the more familiar BuNo’s as used by the Bureau of Aeronautics to identify US Navy and US Marine Corps aircraft and helicopters. Two examples of the Hiller YROE 1 Rotorcycle reside in museums situated within just a few miles of each other. The first specimen ‘4020’ is in a private museum owned by James S Ricklefs of Rick Helicopters Inc. of San Carlos, California. This one has an intact manufacturer’s plate which revealed the following interesting information: Manufacturer’s model 1033: Customers model YROE4: Serial No 6: Customer’s serial No 4020: Contract No 59 6022: Engine type YO 65 2. Accepted 21 June 1960. Manufactured by Saunders Roe Lid. England under agreement from International Engineering Research & Development, Luxembourg under licence from Hiller Aircraft Corporation, USA. Restored by John Trome 1980. The second YROE 1, 14021′, was discovered in The Flying Lady Museum which is owned by Irv and Jan Perch and located at Morgan Hill, near South County Airport, some 65 miles south of San Francisco.
The Turbine Exec is a turbine kit to repower the Rotorway Executive kit helicopter. First flown in April 1997, the US$20,000 kit included the engine, gearbox reduction drive and tail rotor gearbox.
Max speed: 125 mph Cruise: 100 mph Range: 225 sm Rate of climb: 1500 fpm Service ceiling: 13,500 ft Engine: Solar T6Z-T32 hp range: 150-170 Fuel capacity: 35 USG Empty weight: 750 lb Gross weight: 1425 lb Height: 8 ft Length: 22 ft Disk span: 25 ft Seats: 2
