Boeing 273 / XF7B-1       

Designed to meet the requirements of a US Navy specification issued on 6 December 1932, the XF7B-1 (Model 273) was the first all-metal cantilever low-wing monoplane single-seat fighter with a retractable undercarriage, and powered by a Pratt & Whitney SR-1340-30 engine rated at 550hp at 3050m.
The XF7B-1 featured a fully-enclosed cockpit and was flown for the first time on 14 September 1933. Armament comprised two 7.62mm machine guns. After initial evaluation, the XF7B-1 was returned to its manufacturer to have split flaps and a longer-chord engine cowling fitted. Subsequently the enclosed cockpit gave place to an open cockpit. The US Navy considered that the XF7B-1 offered inadequate view and too high a landing speed for shipboard operation, and the sole prototype was scrapped after, in March 1935, the fighter was inadvertently stressed to 12.1g (although the designed load factor was only 9.0) when the pilot pulled out of a 668km/h dive too abruptly following collapse of the windscreen.

Engine: Pratt & Whitney SR-1340-30, 550hp at 3050m
Take-off weight: 1656 kg / 3651 lb
Empty weight: 1262 kg / 2782 lb
Wingspan: 9.73 m / 31 ft 11 in
Length: 8.41 m / 27 ft 7 in
Height: 2.26 m / 7 ft 5 in
Wing area: 19.79 sq.m / 213.02 sq ft
Max. speed: 375 km/h / 233 mph
Range: 1207 km / 750 miles

Boeing 247 / C-73

Derived via the design of the Model 200 Monomail and Model 215 bomber, each of which had a cantilever monoplane wing, Boeing flew the prototype of a new civil airliner which was identified by the company as the Boeing Model 247 on 8 February 1933.
A streamlined low wing monoplane, powered by two 550 hp Pratt & Whitney radial engines, it had retractable landing gear and was the first transport aircraft to have a de icing system for wings and tail unit. Variable pitch propellers gave maximum efficiency for take off and cruising flight, and control surface trim tabs enabled the pilot to ‘balance’ the aircraft so that an automatic pilot could control the machine for long periods. It was also the first twin-engined monoplane airliner able to climb with a full load on the power of only one engine.
With accommodation for a pilot, copilot, stewardess and 10 passengers, sixty examples of the Model 247 were ordered ‘off the drawing board’ to re-equip the Boeing Air Transport System, shortly to become a major limb of United Air Lines, and another 15 were ordered subsequently for companies or individuals.

Boeing 247 Article

The Boeing 247 entered service with United Air Lines in March 1933, with a trans-continental flight time of under 20 hrs. The Boeing 247 entered service with National Air Transport (one of the companies under the United Air Lines umbrella) on June 12, 1933. United took delivery of 59 of the 61 247s built, plus 10 of the 13 improved 247-Ds; earlier 247s were modified to this standard. The sole 247-A was used by the United Aircraft Corp as an executive aircraft.

United bought the 60 Boeing 247’s for $4,500,000.

One built for Roscoe Turner and Clyde Pangborn (to compete in the England-Australia ‘MacRobertson’ air race of 1934) was provided with fuselage fuel tanks instead of the standard airline cabin equipment, and introduced NACA engine cowlings (to reduce drag) and controllable-pitch propellers with optimum settings for take-off and cruising performance. These improvements were incorporated retrospectively on most airline Model 247s, thus elevating them to Model 247D standard.

In the 1936 a Chinese Purchasing Commission approached Boeing for a variant of the Boeing 247D to be built. Designated Model 247Y, the militarised variant had an upper rear gunner position, forward-firing guns in the nose, plus under wing bomb carriers. Kept highly secret, only the one is believed built.

Boeing 247-Y 12 Feb 1937 at Boeing Seattle

When the USA became involved in World War II in late 1941, these Model 247Ds remained in airline use, and 27 of them were impressed for service with the USAAF under the designation C-73. It had been anticipated that they could be used for the carriage of cargo and troops, but it was discovered that the cabin doors were too small for this purpose. Instead, they were deployed to ferry aircrew and, later in the war, were used for training. In service they were provided with 447kW Pratt & Whitney R-1340-AN-1 Wasp radials. When no longer required in late 1944, they were returned to civil airline service.

NC13347 Boeing 247D, serial n°1729 of United Air Lines

Gallery

247
Engines: 2 x 550 hp Pratt & Whitney Wasp
Length: 51.3 ft / 16.25 m
Wing span: 74 ft / 22.6 m
Weight empty: 8,340 lb / 3,780 kg
Crew: 2
Pax cap: 10
Max cruise: 171 mph / 275 kph
Ceiling fully loaded: 18,500 ft / 5,650 km

247D
Engines: 2 x Pratt & Whitney R-1340 Wasp S1H1-G, 550 hp, 410kW
Props: Hamilton Standard hydromatic
Wing span: 74 ft 0 in / 22.56 m
Wing area: 77.6 sq.m / 835.28 sq ft
Length: 51 ft 4 in / 16.25 m
Height: 12 ft 1.75 in / 3.7 m)
Empty weight: 4148 kg / 9145 lb
Max TO wt: 13,650 lb / 6197 kg
Max level speed: 202 mph / 324 kph
Cruise speed: 304 km/h / 189 mph
Ceiling: 7740 m / 25400 ft
Range: 1199 km / 745 miles
Crew: 3
Pax cap: 10

Boeing 266 / P-26 / 281 Peashooter

The Model 248 would form the basis for the P-26, and Boeing created a combat aircraft. A low-wing monoplane with the wing centre section built into the fuselage and also mounting the fixed undercarriage. The wing was fabric-covered and wire-braced and armament would consist of two machine-guns.

After examination, USAAC officials decided that the Model 248 incorporated what they wanted, but there was no budget for a new aircraft. In order to create flying prototypes, the Air Corps and Boeing devised that Boeing would build the airframes at company expense while the Air Corps would supply Boeing with such items as engines, propellers, armament, instruments and other equipment. In a normal military aircraft contract, these items would be supplied to the manufacturer as government furnished equipment (GFE).

This arrangement was mutually advantageous – Boeing could build a new design without going bankrupt while the Air Corps would get a new fighter to test virtually free.

Boeing P-26 Article

Boeing Project Engineer Robert Minshall started work on the Model 248 during September 1931. The aircraft was given the military designation XP-936. Assigned by Wright Field, this designation meant that the Model 248 was the 936th experimental design (military or civil) to be evaluated by Wright Field. A contract for the first three XP-936 aircraft was signed on December 5, 1931.

Since the aircraft was not being developed to strict military guidelines, Boeing was given a free hand,
which meant that the aircraft could be designed and built in a much shorter time period. Construction began in January 1932 and Boeing designers moved into the production areas where drawings could be quickly converted to hardware.

The first XP-936 was completed in little more than 70 days. In order to save more time, the aircraft was not fitted with armament, and test pilot Les Tower took the new aircraft into the air on March 10, 1932.

Flight testing also proceeded at a rapid pace (all structural stress testing was still on paper) and the aircraft showed better performance that the P-12F biplane. After limited flight testing, the aircraft was accepted by the USAAC on April 25 at Wright Field, where more advanced testing by a number of Air Corps pilots would take place.

The three XP-936s should have carried civil registrations. However, they were delivered in the military style paint of the day with XP-936 painted on the airframes, apparently in an effort to make the civil aviation authorities think they were in fact military aircraft.

The second XP-936 had been selected for structural testing. These test aircraft were usually non-flying examples, but this example flew from the outset and was delivered by air to Wright Field. Departing Boeing Field on April 22, the aircraft was flown by Lt. L.H. Dawson – another odd procedure since the aircraft was still Boeing property and probably should have been flown by a company test pilot. Once at Wright, the airframe was statically tested (probably to destruction) and it is very unlikely that the second XP-936 ever flew again.

For the third XP-936, the Air Corps determined that this example would be service-tested by USAAC pilots. Accordingly, the machine went to Selfridge Field in Michigan, departing Boeing on May 6. Once again, the aircraft was flown by a USAAC pilot – Maj. G. Brower and it went to the Ist Pursuit Group where pilots from the group’s three squadrons put the XP-936 through a rigorous flight schedule.

On June 15, 1932, the three prototypes were officially taken over by the Air Corps with the signing of a purchase contract. Army officials noted that the aircraft was an improvement over previous pursuits, but noted their opinion in cautious language since funding was in such short supply.

The three aircraft were given the military designation of XP-26. While test flying the aircraft, 1st PG pilots noted some negative aspects that would have to be corrected, including slow throttle response, long take-off and landing roll, and high take-off and landing speeds. Boeing felt it could make changes in a timely manner and the Air Corps managed to get funding for the new P-26 added to the 1932 Fiscal Year Budget.

The three XP-936 prototypes were essentially handbuilt, so a more economical way of building the fighter was required. Because the P-26 had few straight lines its fuselage had to be covered using long horizontal aluminium strips, beginning at the bottom of the fuselage, each strip overlapping slightly and thus producing a “shiplap” effect.

Stress analysis being a new art, most builders incorporated excessive strength. The P-936’s wing was good for +12g and -4g. When the wing was loaded while inverted it withstood 5g without failure. The flying wires reached +14.25g before failing. The Boeing 109 aerofoil was used.

The wing comprised a centre section integral with the fuselage and carrying the undercarriage and a bomb rack, and two removable outer panels based on two spars of builtup flat sheet aluminium. A generous number of ribs of built-up rolled hatsections and short aluminium tubes contributed to the wing’s strength. A thin sheet-aluminium skin was riveted to the wing structure. The XP-936s had brazier-head (flattishdomed) rivets, but production aircraft had flush riveting to reduce drag. Most of the skinning was anodised to protect against corrosion.

The XP-936’s tailplane began to fail at 90 per cent of its design load (which was 2531b/sq.in), and had to be greatly reinforced. The fin was tested to 130 per cent of its design load (189.61b/sq.ft), Unlike the wing, the tail was of unbraced cantilever design, the all-metal units being built in the spar-and-rib style. Aluminium channel was built into a hinge-line spar, and there was also a diagonal spar. There was no solid leading edge; the upper and lower skins were joined by flush riveting. The ribs did not act as compression members, but were essentially spacers for the aluminium skins.

The control surface hinge lines were channel spars, and pressed aluminium diagonal ribs carried the top and bottom aluminium skins, which were riveted together at the trailing edge. The elevators incorporated the first use in the USA of trim tabs to adjust longitudinal trim in flight. Each aileron had a groundadjustable aluminium trim tab.

The removable welded -steel -tube engine mounting was fixed to the first fuselage bulkhead. Hydropress dies were used to form the smoother panels ahead of the firewall.

The welded steel-tube undercarriage incorporated a rigid ‘V’ structure attached to the wing root spars that also provided an anchor for the flying wires. Boeing-built oleopneumatic shock struts were used. Each leg held just the inboard axle end, allowing easy removal of the wheel and tyre, The undercarriage was faired with aluminium, and the wheel spats were press-formed from aluminium sheet and attached to the shock strut so that the spat moved with the strut. The undercarriage could become unstable with the flying wires loosened or removed, so a spreader bar was added between the undercarriage legs.

Fuel was carried in a main tank in the fighter’s belly, holding 55 US gal, plus removable 26 US gal tanks in each wing root. There was an 8 US gal oil tank in front of the first bulkhead. The cylinders were encircled by a Townend ring to reduce drag.

The two 0.30in-calibre Browning machine-guns could be changed for a 0.30in gun on the port cockpit floor and a 0.50in gun to starboard. The smaller-calibre weapons had 500 rounds each, but only 200 rounds were provided for the 0.50in gun. A Type A-3 underfuselage munitions rack carried a range of light ordnance.

Once contracts were in place and construction on the P-26A had started, few problems were encountered and production gathered pace. By June 1934 all 111 production examples had been delivered.

The first production run averaged out at $9,999 for each aircraft, but this did not include the government furnished equipment (GIFIE) such as engines, radios and armament. The rapid delivery also meant that problems inherent with the design had not really been rectified.

While squadrons were getting used to the type, the global financial and political situation was changing. American expenditure on military aircraft had risen from $25m for the fiscal year 1925 to $69m for FY 1931, and increasing political tensions around the world had led to an arms race. During 1935, the Italian leader Benito Mussolini had given orders to attack Ethiopia while Hitler made his new Luftwaffe public.

XP-936

In the USA the new Roosevelt administration was backing drastic social reforms to ease the nation out of the grips of the Great Depression, and also allocating unprecedented funds for military aviation. The Baker Board recommended that the Air Corps increase its inventory to 2,320 aircraft while a General Headquarters Air Force (GHOAF) was established for operations not dependent on ground forces. Officially begun in March 1935, the GHOAF had been structured so that its aircraft could be concentrated for a military attack in any direction.

The GHOAF comprised all the attack, bomber and fighter units in the USA, but excluded observation units and five PGs deployed overseas. Between June 1932 and January 1940, total Air Corps strength consisted of 15 Groups. The general staff in charge of operations saw little use for additional aircraft and rarely expended all the funds assigned. Into all this planning came the force of Peashooters.

The aircraft went to the l st, 17th, and 20th PGs. For the pilots, their only training came in the form of reading extremely condensed pilot’s notes. Tactics related mainly back to lessons learned during World War One.

One major design problem became apparent on February 22, 1934, when Lt Frederick Patrick was killed when his P-26A, serial 33-46, tipped over during a forced landing. The aircraft received little damage but the headrest broke off and Patrick’s neck was broken. The fleet was grounded while Wright Field and Boeing worked on a fix. A new headrest, some 8 in higher, that could resist a 27,6001b vertical load, was developed and installed on 33-56, which had yet to be delivered. All aircraft at the factory were thus modified and deliveries resumed on March 27. All other aircraft were modified in the field, work being completed by May 21.

The aircraft’s tailplane was easily damaged by rocks and gravel when operating from rough fields, so sheet rubber was added to the lower leading edge of the unit, leading to speculation that the P-26 was fitted with de-icers. It wasn’t.

Pilots converting from biplane fighters found the Peashooter’s landing speed – 82 mph. – to be disconcertingly high. The National Advisory Committee for Aeronautics (NACA), Boeing and the Air Crops worked on the problem and developed four different types of flaps which were tested in the wind tunnel at Langley Field, Virginia, using 33-56 as a guinea pig. It appears that the least effective unit was chosen by Wright Field, installed on 33-28 which, when flight tested, crashed because the flaps blanked out the tail surfaces during approach (which NACA had predicted).

Boeing developed a flap system that was complex and expensive to produce. These were tested on the first of the export variant, the Model 281, which was sent to Wright Field for testing. These flaps brought the landing speed down to 73 mph and the Air Corps accepted the design. In May 1935, Boeing began to receive the P-26 fleet for flap fitting. The first unit to arrive was the 17th PG from March Field, California. This unit had been redesignated as an attack group and would soon give up the Peashooters for more effective equipment. All the P-26s had been fitted with flaps by November 1935.

Pilots who undertook high-g manoeuvres found that certain aircraft were developing skin wrinkles between the tail and cockpit. Boeing recommended a strengthening of the fuselage. Part of the skin was removed so that structural modifications could be made. Also, a new tailwheel assembly was added to improve ground handling.

Although the P-26 was used mainly for daylight operations, pilots complained about exhaust glare in flight during night or twilight conditions. Accordingly, the exhaust system was modified to prevent this problem. Also, pilots found that the pitot tube on the starboard wing would vibrate heavily in flight. Boeing reduced the size of the tube, but this gave inaccurate airspeed readings and a final fix was accommodated by adding a more rigid pitot tube.

Once in service, the P-26 demonstrated a problem that could not be fixed, however. The narrow undercarriage, high centre of gravity and spongy shock absorbers resulted in many nose-overs. The remedy was to issue bulletins to pilots on how to avoid this occurrence.

With the aircraft distributed to the three Groups, the usual flying took place with units practicing tactics, formation flying, cross-country flights and participating in war games. The P-26 was quickly eclipsed by the Seversky P-35 and Curtiss P-36 and Peashooters began to go to second and third-line units.

During 1938, the 18th PG received at least 42 P-26s for the defence of Hawaii. Although these machines were theoretically phased out by the time of the Japanese attack on Hawaii on December 7, 1941, at least a dozen were present at Wheeler Field. One account states that none of these aircraft received damage; another proclaims that several were destroyed or damaged.

The Peashooter apparently did not take any part in the defence of Pearl Harbor, and those remaining may have been retained as hacks or advanced trainers. Thus, the service life of the Peashooter was brief and while the aircraft introduced new features it was also a design that was obsolete from the start. It was also the last production fighter design built by Boeing.

Boeing decided to create an export variant of the P-26A as the Boeing Model 281. This was essentially a standard P-26A airframe with equipment added per the customer’s order. Reasoning that these aircraft would be operated off fields more primitive than the American military, Boeing made a study on how to reduce the aircraft’s comparatively high landing speed. The first Model 281 (c/n 1959, carrying American civil registration X12771), made its first flight on August 2, 1934. The aircraft was painted in standard Air Corps colours of Olive Drab and Chrome Yellow. After several flights, Boeing installed split trailing-edge flaps which reduced the landing speed. The Air Corps took note and accordingly had their P-26As retrofitted.

At this time, there was a great deal of upheaval in China as various factions fought for control – all the while being watched by Japan. Using company money, Boeing sought out further interest from the Chiang Kaishek government. Meanwhile, the Model 281 was tested with revised wheel fairings more suited to primitive environments and the aircraft was tested with Goodyear Airwheels for use on undeveloped fields.

An order for ten Model 281s for China was finally received, and much of the purchase money was raised by the Chinese community in America. Deliveries of the Model 281 were made between December 2, 1935, and January 5, 1936.

The Chinese 281s were dismantled after test flights and then sent by ship to China where they were reassembled and test-flown. The aircraft were based at Chuying airfield, near Nanking. By this time, invading Japanese forces had begun to overwhelm Chinese forces, and Nanking was an inviting target for “Nell” bombers operating from Taipei on Formosa (now Taiwan).

It is not known if the Japanese were aware of the ten Model 281s based at Nanking, or whether some of them were being flown by mercenary pilots. On August 20, 1937, a force of “Nell” bombers set forth to attack Nanking, all with inadequate defensive armament and without fighter escort (the fighters simply did not have the range). As the bombers arrived over Nanking, they were met by the 281s. Six of the Mitsubishis were destroyed and one of the 281s received light damage. The Japanese seemed to be willing to accept the losses and kept sending the bombers to attack Chinese targets. After securing bases on the mainland, the bombers were able to conduct raids deep into China.

Although records are incomplete, it appears that the Boeings continued to score successes. However, lack of spare parts and the introduction of Japanese fighters into combat meant that when Nanking fell on December 13, 1937, none of the Boeings was airworthy.

During this troubled period, Spain also took interest in the Model 281 and X12275 (c/n 1962) was shipped across the Atlantic and reassembled for test flying at Barajas airfield near Madrid on March 10, 1935. A contract had originally been signed by the Direccion General de Aeronjutica on January 16, 1935, with Boeing and an individual named Alfonso Albeniz. The fighter was demonstrated to the Spanish by company test pilot Les Tower with Boeing vice-president Erik Nelson in attendance.

The Spanish liked the Model 281, but they did not like the price. Accordingly, during June 1935, the Spaniards contracted with Hawker Aircraft in the UK for 50 Fury biplane fighters to be built under licence by Hispano-Suiza.

The Model 281 did not return to Seattle but remained at Barajas. When the Spanish Civil War started on July 17, 1936, the 281 was flown to Cuatro Ventos airfield near Madrid. The aircraft had arrived in Spain with no armament and no synchroniser gear so the Spaniards modified the aircraft to mount two British Vickers machine-guns in pods under the wings, after which the Republican Boeing began flying combat missions.

American mercenary pilot Eugene Finnick described the Boeing as “an old rattletrap”. However, the Boeing kept operating and by mid-October 1936 it was one of only three operational fighters left at Getafe. On October 21, it was shot down in a battle with three Fiat CR.32s over the airfield. Pilot Ramon Puparelli escaped by parachute, but the combat career of the sole Spanish 281 was most definitely over.

Sometime later, the Spanish embassy in Paris paid Wilbur Johnson (a Boeing representative) $20,000 for the aircraft.

In addition Panama and Guatemala received ex-USAAC P-26. The ones left by the US army to the Guatemalan Air Force were sold for $1 each as PT-26; that is, trainers, to allay political misgivings. They were very manoeuvrable, and were named “mosquitos” locally, because the peculiar sound made by their motors. They were still in service by 1954.

In total, only 136 P-26s were built.

The Model 224 would later be refined into the Model 264 and the Air Corps would eventually acquire three as the P-29.

P-26A

Gallery

Replica:
WAR aircraft P26 Peashooter
Mayocraft Inc P26 Peashooter

Variants:
P-936
USAAC experimental designation for first three Model 248 aircraft. Two flown, one used for static testing

P-26
Designation applied to P-936 on June 15, 1932. USAAC serials 32-412-414

YIP-26
Service test designation for P-936

XY1P-26
Applied in August 1932 as an apparent paperwork combination of the above designations

Y.26
Standard designation applied to the first aircraft

P-26A
First production order for 111 examples. USAAC serials 33-28-138

P-26B
Two of the 25 aircraft added to the above order fitted with fuel-injection engines and wing flaps. USAAC serials 33-179 and 33-180

P-26C
25 aircraft added to the P-26A order with minor differences. After about a year of service, all were modified to P-2B standard. USAAC serials 33-181, 33-183-203

Model 281
Export version of P-26A to China and Spain. Boeing c/ns 1959-1962,1965-1972

RP-26
Designation applied on October 22, 1942, to surviving USAAC P-26s to indicate they were obsolete and restricted from combat action

ZP-26
Order issued on December 11, 1942, regarding P-26As too old to fit into the RP designation

PT-26A
Paperwork designation applied for political reasons to the examples supplied to Guatemala

Specifications:

XP-936
Engine: Pratt & Whitney R 1340-1, 525 hp
Wingspan: 27 ft 5 in
Length: 23 ft 9 in
Height: 7 ft 6 in
Wing area: 149.512 sq.ft
Max take off weight: 2789 lb
Weight empty: 2120 lb
Fuel: 50-106 USG
Max. speed: 227 mph at 6000 ft
Cruising speed: 193 mph
Landing speed: 73.5 mph
Ceiling: 27800 ft
Climb: 2230 fpm
Crew: 1

Boeing P-26A Peashooter
Engine: 1 x Pratt and Whitney R-1340-27, 600hp.
Length: 23.82ft (7.26m)
Wingspan: 27.95ft (8.52m)
Height: 10.40ft (3.17m)
Empty Weight: 2,273lbs (1,031kg)
Maximum Take-Off Weight: 3,012lbs (1,366kg)
Fuel: 52-107 USG
Maximum Speed: 227mph (365kmh; 197kts)
Cruise: 199 mph
Landing speed: 82.5 mph
Maximum Range: 360miles (579km)
Rate-of-Climb: 2,360ft/min (719m/min)
Service Ceiling: 27,395ft (8,350m)
Armament: 2 x 7.62mm machine guns
Accommodation: 1

Boeing 281
Engine: 1 x Pratt and Whitney R-1340-33, 600hp.
Length: 23.82ft (7.26m)
Wingspan: 27.95ft (8.52m)
Height: 7 ft 10.5 in
Empty Weight: 2,354lbs
Gross weight: 3039 lb
Maximum Take-Off Weight: 3,390 lb
Fuel: 55-107 USG
Maximum Speed: 235mph at 6000 ft / 215 mph at SL
Cruise: 210 mph
Landing speed: 68 mph
Maximum Range: 360miles (579km)
Rate-of-Climb: 2,360ft/min (719m/min)
Service Ceiling: 28,200 ft
Armament: 2 x 7.62mm machine guns
Accommodation: 1

Boeing 214 Y1B-9 / 215 XB-901 YB-9 / 246 Y1B-9A

In 1930 Boeing began the private-venture development of a bomber aircraft based on the Model 200 Monomail. The resulting prototypes and service evaluation bombers were scaled-up versions of this aircraft. They differed by having twin-engines, installed in nacelles at the wing leading edge, and by adaptation of the fuselage to cater for the crew and weapons.

Y1B-9A

To provide the crew accommodation, the fuselage was extended forward of the wing. A bomb-aimer/gunner was accommodated in the nose and immediately behind him, within the fuselage, was a radio operator’s position. Aft of the radio operator were two cockpits in tandem, for pilot and co-pilot, with a fourth open cockpit, just aft of the wing trailing edge, for the rear gunner. A bombload totalling 1025kg could be divided between an internal bomb bay and underwing racks.

Y1B-9

First flying, on 13 April 1931, was the Boeing Model 215, powered by two 429kW Pratt & Whitney R-1860-13 Hornet radials. This was tested by the USAAC under the initial designation XB-901 (Experimental Bomber), and satisfactory conclusion of testing resulted in the procurement of this aircraft under the designation YB-9. At the same time the then incomplete Boeing Model 214 was contracted under the designation Y1B-9, plus five additional service test aircraft with the designation Y1B-9A (Model 246).
The Model 214, powered by 447kW Curtiss V-1570-29 Conqueror inline engines, was flown for the first time on 5 November 1931, and following further tests, the Model 214 was re-engined with a supercharged version of the Pratt & Whitney Hornet. This power-plant was chosen also for the Y1B-9As, the first of which was flown on 14 July 1932. The Y1B-9A differed externally from the earlier prototypes in having modified vertical tail surfaces, and had internally a number of equipment and structural changes to meet service requirements.
Subsequent testing, and evaluation against the Martin Model 123, resulted in the Martin aircraft entering service as the B-10. This came as a great disappointment to the Boeing company, which had produced this bomber with performance superior to most contemporary fighter aircraft.

Boeing 215 / XB-901 / YB-9
Engines: 2 x Pratt & Whitney R-1860-13 Hornet radials, 429kW

Boeing 214 / Y1B-9
Engines: 2 x Curtiss V-1570-29 Conqueror inline, 447kW
re-engined with 2 x 447kW Pratt & Whitney SR-1860-11 Hornet supercharged radial piston

Boeing 246 / Y1B-9A
Engine: 2 x Pratt & Whitney SR-1860-11 Hornet, 447kW / 600 hp
Take-off weight: 6495 kg / 14319 lb
Empty weight: 4056 kg / 8942 lb
Wingspan: 23.42 m / 76 ft 10 in
Length: 15.77 m / 51 ft 9 in
Height: 3.66 m / 12 ft 0 in
Wing area: 88.63 sq.m / 954.00 sq ft
Max. speed: 299 km/h / 186 mph / 163kt
Cruise speed: 266 km/h / 165 mph
Ceiling: 6325 m / 20750 ft
Rate-of-Climb: 900ft/min (274m/min)
Range: 869 km / 540 miles
Armament: 2-4 x 0.30 caliber machine guns
Bombload: 2,260lbs
Accommodation: 4 or 5

Boeing 202 / XP-15 / 205 / XF5B-1

Model 205

During 1929, work began as a private venture on two prototypes of a single-seat parasol fighter monoplane, one (Model 202) being intended for the USAAC and the other (Model 205) having arrester gear for US Navy evaluation. The Models 202 and 205 featured a semi-monocoque metal fuselage and metal wings, with smooth, non-stressed metal skinning. Provision was made for the standard twin 7.62mm gun armament and the Model 205 could carry a single 227kg bomb or five 13kg bombs.

Model 202 XP-15

The Model 202 had a Pratt & Whitney SR-1340D Wasp rated at 450hp at 2438m and the Model 205 had an SR-1340C rated at 480hp at sea level. The Model 202 was flown in January 1930, and was unofficially assigned the designation XP-15 when evaluated by the USAAC. During evaluation it was fitted with a ring cowling and revised vertical tail surfaces, but was rejected by the USAAC and eventually crashed on 7 February 1931 after propeller failure. The similar Model 205 was assigned the designation XF5B-1, and underwent modifications identical to those applied to the Model 202. Flown in February 1930, the XF5B-1 was used for experimental purposes for three years, no production being undertaken.

Model 205 XF5B1

Model 202 / XP-15
Engine: Pratt & Whitney SR-1340D Wasp, 450hp at 2438m
Take-off weight: 1245 kg / 2745 lb
Empty weight: 931 kg / 2053 lb
Wingspan: 9.29 m / 30 ft 6 in
Length: 6.40 m / 20 ft 12 in
Height: 2.84 m / 9 ft 4 in
Wing area: 14.61 sq.m / 157.26 sq ft
Max. speed: 298 km/h / 185 mph

Model 205 / XF5B-1
Engine: Pratt & Whitney SR-1340C, 480hp

Boeing 200 Monomail / 221 Monomail

200 Monomail

Boeing began the development of an advanced cargo/mail-carrying aircraft in 1929.

Boeing 200 / 221 Monomail Article

A cantilever low-wing monoplane of all-metal construction, the Boeing Model 200 Monomail benefited by the cantilever wing eliminating drag-inducing struts and bracing wires. The a semi-monocoque fuselage structure provided a more streamlined shape, the semi-retractable tailwheel landing gear ensured that most of the main unit structure was retracted within the wing, and the Pratt & Whitney Hornet B radial engine was surrounded by an anti-drag cowling. It retained an open cockpit for the pilot, seated well aft, and the forward cargo/ mail compartments.

First flown on 6 May 1930, the Monomail was used for a number of tests and experimental flights before entering service on Boeing Air Transport’s San Francisco – Chicago route in July 1931. The aircraft did not achieve a single order beyond the prototype.

Generally similar to the Model 200 Monomail, this single aircraft had a fuselage lengthened by 0.2m and cargo/mail capacity reduced from 1043kg to 340kg, to provide accommodation for six passengers in an enclosed cabin; first flown on August 1930, and entered service with Boeing Air Transport

221 Monomail

Boeing Model 221A: designation applied to the Models 200 and 221 following fuselage ‘stretches’ to provide accommodation for eight passengers; both saw service on the Cheyenne-Chicago route of Boeing’s newly-formed United Air Lines

The advanced design of this aircraft led to development of the Model 214 and Model 215 experimental bombers, and two variants of this basic civil design.

Boeing Model 200
Engine: 1 x 429kW Pratt & Whitney Hornet B radial
Take-Off Weight: 3629 kg / 8001 lb
Empty Weight: 2158 kg / 4758 lb
Wingspan: 18.02 m / 59 ft 1 in
Length: 12.56 m / 41 ft 2 in
Max. Speed: 254 km/h / 158 mph
Cruise Speed: 217 km/h / 135 mph
Ceiling: 4265 m / 14000 ft
Range: 853 km / 530 miles

Boeing 236 / F6B / BFB-1

XF6B1

The last Boeing biplane fighter, the Model 236 single-seat shipboard fighter was designed around the 14-cylinder twin-row Pratt & Whitney R-1535 Twin Wasp Junior engine rated at 625hp at 1676m. Of all-metal construction with fabric-covered wings, the Model 236 was assigned the designation XF6B-1 by the US Navy and flew on 1 February 1933.
Armament was two 7.62mm guns and provision was made for a single 227kg bomb or two 52kg bombs, and on 21 March 1934, the prototype was assigned the new “bomber-fighter” designation of XBFB-1. The engine installation and undercarriage were refined during the test and evaluation programme, but no production was undertaken.

Engine: Pratt & Whitney R-1535 Twin Wasp Junior, 625hp
Take-off weight: 1680 kg / 3704 lb
Empty weight: 1038 kg
Wingspan: 8.69 m / 28 ft 6 in
Length: 6.74 m / 22 ft 1 in
Height: 3.22 m / 10 ft 7 in
Wing area: 23.41 sq.m / 251.98 sq ft
Max. speed: 322 km/h / 200 mph
Range: 845 km / 525 miles

Boeing 93 / XP-7

The final production PW-9D (the 16th) was retained by Boeing for the experimental installation of a 600hp water-cooled Curtiss Conqueror V-1570 engine and, as the XP-7 (Model 93), was eventually delivered to the USAAC on 4 September 1928. Distinguished from the PW-9D by a shorter, deeper nose with a larger radiator, the XP-7 enjoyed some success during trials, proving the suitability of the Conqueror for fighter installation. Proposals to build four service evaluation P-7s were abandoned when it was concluded that the basic PW-9 airframe had reached the limit of its development. The XP-7, the last Boeing fighter biplane to employ a liquid-cooled engine, was reconverted to PW-9D standards.

Engine: 600hp water-cooled Curtiss Conqueror V-1570
Take-off weight: 1479 kg / 3261 lb
Empty weight: 1 053 kg
Wingspan: 9.75 m / 31 ft 12 in
Length: 7.31 m / 23 ft 12 in
Height: 2.74 m / 8 ft 12 in
Wing area: 22.39 sq.m / 241.00 sq ft
Max. speed: 269 km/h / 167 mph

Boeing 83 / 89 / 99 F4B / 100 / 102 P-12

Both Models 83 and 89 were Navy designated Boeing XF4B-1 fighters. The difference was the Model 83 had a spreader-bar axle landing gear, and an arrester hook. The Boeing Model 89 had a split-axle landing gear so that a 500 lb bomb could be carried beneath the fuselage.

Boeing F4B Article

A private venture built at Boeing’s expense, the XF4B-1 first flew on 7 August 1928. It was placed in production as the Boeing 99 for the Navy F4B-1 series and Model 102 for Army P-12 series, 27 were ordered as F4B-1, and was first delivered in July 1928.

Flying the Boeing P-12

The P-12 was constructed of dural tubing, fabric covered and having wooden wings with corrugated metal control surfaces. Powered by a Pratt & Whitney R-1340 Wasp of 450 hp, the top speed was 171 mph and ceiling 29,000 ft fully loaded.

Model 102 P-12

One XP-12A was built as a test vehicle for the newly NACA cowl. The fuselage was flared to conform to the enlarged nose and shorter landing gear was installed. The XP-12A was a modification of the 10th production P-12. It was later destroyed in a crash.
The original P-12 and P-12B were the only two P-12 models that were not equipped with a speed-ring cowl.

XP-12A

The USAAC ordered ten aircraft similar to the F4B-1 in late 1928, accepting the naval evaluation as being correct. Designated P-12, these differed only by having the arrester hook and other specifically naval equipment deleted. P-12B, of which 90 were built with 317kW Wasp engines, differed very slightly with Frise balanced ailerons and internal improvements and were followed by 96 P-12C, which were similar to the Navy’s F4B-2. P-12D, of which 35 were built, had a more powerful 391kW Wasp engine.

The P-12C and P-12D models were improved models and utilised improved and heavier constructed cross-axle landing gear and a speed ring cowl around a Pratt & Whitney Wasp of 550 hp. Many P-12C and D models were fitted later with P-12E type vertical tail surfaces to give better control.
The P-12E introduced an all metal monocopue fuselage with greater greater structural rigidity of the fuselage for higher G loads. Most extensively built of the Army versions was the P-12E. This had a pilot’s headrest faired by a turtleback and the more powerful engine of the P-12D. A total of 135 were ordered in 1931, many remaining in service until replaced by P-26A in 1935. The last few of the order were given 447kW / 550 hp Pratt & Whitney R-1340-19 Wasp engines and the designation P-12F. The P-12F had a top speed of 195 mph and ceiling of 32,000 ft.
The P-12F had a swivel tail wheel in place of a skid. All P-12s in service were later fitted with tail wheels.

Model 218 c/n 1260

The Boeing Model 218 (XP-925H) was the prototype of the P-12E/F4B-3 series. With a 500 hp Pratt & Whitney Wasp engine the P-12E had a top speed of over 190 mph and a service ceiling of 27,000 ft fully loaded.
One P-12E was fitted with a special cockpit enclosure and others had “Panama Conversion Kits” installed.
Experimental test models included;
XP-12G – turbo-supercharged Wasp engine and 3 blade propeller.
XP-12H – basic P-12D with a geared Wasp engine instead of the usual direct drive.
P-12L – engine test model.
P-12J – engine test model.
P-12K – P-12Es modified for fuel injection.

Forty-six F4B-2, delivered in early 1931, had the spreader-bar axle, a tailwheel, Frise ailerons and a neat ring cowling for the engine. They were followed by 21 F4B-3 with a semi-monocoque metal fuselage and 92 F4B-4 which differed by having a larger fin and rudder.

F4B-2 USN

The F4B-3 and P-12E were identical except for the carrier hook, cabane wire, and double row of rivets, and a tall radio mast on the F4B-3. The F4B-4 served the US Navy and US Marines.

F4B-3 Marines

The Navy bought 94 F4B-4s, 21 going to the Marine Corp to operate from land bases.

The Boeing 100 of 1929 was an ATC’d civil version of the P-12 built as a sport plane and for export. They were lighter in weight and the early models resembled the P-12B in appearance. Seven were built and owners included Howard Hughes, Art Goebel, Tex Rankin and Paul Mantz, as well as several foreign governments. Howard Hughes one was delivered as a two-seater as Model 100-A. Hughes soon had it reconverted to one seat, and it survived as such until 1958.

Model 100-A

It was reported in September 1956 that the sole Boeing 100-A, N247K, crashed at Dallas, USA, killing the owner -pilot, Robert Hallbeck. Hallbeck was rolling the machine at about 3000 ft when one of the wings collapsed, and although he was wearing a parachute he was unable to jump clear.

The Japanese imported a civil Boeing 100 and two Boeing 100Es were exported to Siam in September 1931.

Boeing 100E

One Boeing 100E survives on display at the Kings Museum, Bangkok, Thailand.
Fourteen F4B-4s were exported to Brazil before World War 2.
A total of 554 in the P-12 – F4B series were built, 110 of which were P-12Es. The one surviving P-12E is on display in “The Air Museum”, Ontario International Airport, Ontario, Canada.

Boeing 100E

P-12/F4Bs saw service in Panama, Hawaii and the Phillipines. A few went to China and one of them was the first American made plane to shoot down a Japanese plane in combat prior to World War 2.
Two F4B-4 Navy aircraft were released to the CAA Air Safety Board during the early 1930s. Later sold to private buyers, they were used in many pre-war and post-war airshows. One was owned by Hyland Flying Service, Rochester, New York, was later acquired by the Smithsonian Institute and placed on loan to the Navy Museum, fully restored.

Gallery

75% replica: Reid Boeing P-12E
Aero-Tech Boeing F4B-2/P-12C

Boeing F4B / P-12
Engine: 1 x Pratt & Whitney R-1340-D Wasp
Length: 20.08ft (6.12m)
Width: 29.99ft (9.14m)
Height: 9.32ft (2.84m)
Empty Weight: 2,355lbs (1,068kg)
Maximum Take-Off Weight: 3,611lbs (1,638kg)
Maximum Speed: 188mph (303kmh; 164kts)
Maximum Range: 370miles (595km)
Rate-of-Climb: 1,666ft/min (508m/min)
Service Ceiling: 26,903ft (8,200m)
Armament: 2 x 7.62mm machine guns
Accommodation: 1

Variants:

Boeing 83 / XF4B-1
Number built: 1
Serial number / Registration: 8129
First flight: 25 June 1928
Bought by Navy 19 June 1929.

Boeing 89 / XF4B-1
Number built: 1
Serial number / Registration: 8128
First flight: 7 August 1928
Bought by Navy 19 June 1929.

Armament: 500 lb bomb

Boeing 99 / F4B-1
Number built: 27
Serial number / Registration: 8130-8156
First flight: 6 May 1929
Production version of 89. Navy sn8133 converted to executive model.

Boeing 100
Number built: 4
Serial number / Registration: NS-21, NC872H, C873H, NC874H
First flight: 18 October 1929
Civil version of 83/89.

Boeing 100A
Number built: 1
Serial number / Registration: 247K
First flight: 26 July 1929
Howard Hughes 2 seat version.

Boeing 100E
Number built: 2
Serial number / Registration:
First flight:
Siam P-12E export version.

Boeing 100F
Number built: 1
Serial number / Registration: X10696
First flight: 20 June 1932
Civil P-12F testbed for Pratt & Whitney.

Boeing 101 / XP-12A
Number built: 1
Serial number / Registration: 29-362
First flight: 10 May 1929
Destroyed in mid-air collision.

Boeing 102 / P-12
Number built: 9
Serial number / Registration: 29-353 – 29-361
First flight: 11 April 1929
83, 89 Army version.

Engine: Pratt & Whitney R-1340 Wasp, 450 hp
Top speed: 171 mph
Ceiling at MAUW: 29,000 ft

Boeing 102B / P-12B
Number built: 90
Serial number / Registration: 29-329 – 29-341, 29-433 – 29-450, 30-29 – 30-87
First flight: 12 May 1930

Engine: Pratt & Whitney R-1340 Wasp, 317kW

Boeing 218 / XP-925
Number built: 1
Serial number / Registration: X66W
First flight: 29 September 1930
Army revised P-12B, prototype P-12E & F4B-3.

Engine: Pratt & Whitney R-1340 Wasp, 500 hp
Top speed: 190+ mph
Service ceiling at MAUW: 27,000 ft

Boeing 222 / P-12C
Number built: 96
Serial number / Registration: 31-147 – 31-229, 31-230 – 31-242
First flight: 31 January 1931
131 ordered, last 35 built as P-12D.

Engine: Pratt & Whitney R-1340 Wasp, 391kW / 550 hp

Boeing 223 / F4B-2
Number built: 46
Serial number / Registration: 8806, 8613-8639, 8791-8809

Engine: Pratt & Whitney R-1340 Wasp, 391kW / 550 hp

Boeing 227 / P-12D
Number built: 35
Serial number / Registration: 31-243 – 31-277
First flight: 2 March 1931
Improved P-12C, last 35 P-12C built as P-12D.

Engine: Pratt & Whitney R-1340 Wasp, 391kW / 550 hp
Top speed: 188mph

Boeing 234 / P-12E
Number built: 110
Serial number / Registration: 31-553 – 31-586, 32-1 – 32-76
First flight: 15 October 1931
Production 218 models, 1 converted to P-12J, 7 to P-12K.

Engine: Pratt & Whitney R-1340E Wasp, 391kW / 550 hp, 500 hp at 6000 ft
Engine compression ration: 6:1
Overall span (Upper): 30 ft
Length: 20 ft 4 11/16 in
Height: 8 ft 9 in
Airfoil section: Boeing 106
Total wing area: 227.5 sq.ft
Upper wing span: 30 ft
Upper wing chord: 60 in
Upper wing diherdral: 0 degs
Upper wing area: 141.4 sq. ft
Lower wing span: 26 ft 4 in
Lower wing chord: 45 in
Lower wing diherdral: 2 degs
Lower wing area: 86.1 sq. ft
Empty weight: 1981.5 lb
Fuel: 300 lb
Wing loading: 11.75 lb/sq.ft
Loaded weight: 2674.3 lb
Landing speed; 59 mph
Cruise speed: 167 mph
Max speed: 190 mph
Range at cruise: 475 miles
Armament: 2 x .30 Browning 30M mg or 1 x .30 mg and 1 x .50 mg, and 2 x M-3 bombs

Boeing 235 / F4B-3
Number built: 21
Serial number / Registration: 8891-8911
Production 218 models.

Engine: Pratt & Whitney R-1340D Wasp, 391kW / 550 hp
Speed: 187 mph at 6000 ft
Empty weight: 2200 lb
Armament: 2 x .30 Browing mg or 1 x .30 and 1 x .50 cal mg

Boeing 235 / F4B-4
Number built: 92
Serial number / Registration: 8912-8920, 9009-9053, 9226-9263
Improved F4B-3, larger tail. 14 to Brazil.

Engine: Pratt & Whitney R-1340D Wasp, 500 hp
Speed: 187 mph at 6000 ft
Empty weight: 2312 lb
Armament: 2 x .30 Browing mg or 1 x .30 and 1 x .50 cal mg

Boeing 251 / P-12F
Number built: 25
Serial number / Registration: 31-77 – 31-101
Improved P-12E.

Engine: Pratt & Whitney R-1340-19 Wasp, 447kW / 550 hp
Top speed: 195 mph
Ceiling: 32,000 ft

Boeing 256 / “1932”
Number built: 14
Export F4B-4s from Navy order to Brazil.

Boeing 267 / F4B-3 / P-12E
Number built: 9
F4B-3 fuselage, P-12E wings. Light export model to Brazil.

XP-12G
turbo-supercharged Wasp engine and 3 blade propeller.

XP-12H
basic P-12D with a geared Wasp engine instead of the usual direct drive.

P-12L
engine test model.

P-12J
engine test model.

P-12K
P-12Es modified for fuel injection.

Boeing 80

The growth of operations on Boeing Air Transport’s San Francisco-Chicago route resulted in the design and development of a purpose-designed passenger transport, the Boeing Model 80, first flown during August 1928. A large unequal-span biplane, with the lower wing of reduced chord, the Model 80 had a wing structure of wood, fabric-covered, and a fuselage and tail unit of welded steel tube, also fabric-covered. Landing gear was of fixed tailwheel type, and power was provided by three 306kW Pratt & Whitney Wasp radial engines. These were mounted in tri-motor configuration, one in the fuselage nose, and one each side of the fuselage, between the biplane wings.
The main cabin of the Model 80 accommodated 12 passengers, plus a flight stewardess. Boeing stewardesses were all registered nurses. The Model 80 provided a separate enclosed flight deck for the pilot and co-pilot/navigator. Four of these aircraft were built, entering service with Boeing Air Transport in the late summer of 1928.

The Model 80s were followed by 10 of the improved Model 80A, this type having more powerful Pratt & Whitney Hornet engines, refinements to the wing, improved streamlining and, because of the increased power available, a cabin layout to accommodate a maximum of 18 passengers.

80A

Some pilots insisted on an open cockpit. One Model 80 was re-designed as the Model 80B with open cockpit and raised seats.

80B

The 80B was rebuilt to 80A configuration at the insistence of the majority.

Gallery

Boeing 80
Engines: 3 x Pratt & Whitney Wasp, 306 kW
Passengers: 12

Boeing 80A-1
Engines: 3 x 391kW Pratt & Whitney Hornet radial piston
Take-off weight: 7938 kg / 17500 lb
Empty weight: 4800 kg / 10582 lb
Wingspan: 24.38 m / 79 ft 12 in
Length: 17.22 m / 56 ft 6 in
Height: 4.65 m / 15 ft 3 in
Wing area: 113.34 sq.m / 1219.98 sq ft
Max. speed: 222 km/h / 138 mph
Cruise speed: 201 km/h / 125 mph
Ceiling: 4265 m / 14000 ft
Range: 740 km / 460 miles
Passengers: 18