Lak LAK-14 Strazdas

The LAK-14 Strazdas (Thrush) was designed at LAK by Antanas Paknis, one of the organization’s original design team. Like other LAK designs it developed the aeronautical use of glass fibre, foams and other novel materials. It was intended to succeed the Oskinis BRO-11M, also known as the LAK-2. It was therefore in competition with the Oškinis BRO-23KR Garnys.

The Strazdas had an externally more conventional fuselage, though its construction was more advanced. One of LAK’s founding goals was to develop the aeronautical use of plastics and composites, so the forward fuselage of the Strazdas, apart from a wooden nose fairing which held the launch towing hook, was built from three-ply glass fibre with foam filling. The pilot sat in a long, open cockpit with the seat back against a pedestal that supported the wing. This pedestal was part of the enclosed, round-sectioned rear fuselage structure which also included an integral fin. The tailplane, mounted high on the fuselage, had foam ribs and two-ply glass cloth skin.

The two-part, rectangular plan wing of the Strazdas was mounted high on its pedestal with 5° of dihedral. It was built around single spars, each braced to the lower fuselage with a single strut. Early development aircraft had wooden spars and ribs with glass cloth covering. Slotted, broad chord ailerons filled the whole trailing edge.

First flown in 1981, production began early in 1981. The first production aircraft had wooden spars but this was later replaced by integrated glass fibre reinforced polyester resin structures. Production continued until 1985.

Wingspan: 7.34 m (24 ft 1 in)
Wing area: 10.60 m2 (114.1 sq ft)
Aspect ratio: 5.1
Airfoil: TsAGI R-P
Length: 5.25 m (17 ft 3 in)
Height: 2.30 m (7 ft 7 in)
Empty weight: 100 kg (220 lb)
Max takeoff weight: 185 kg (408 lb)
Maximum speed: 100 km/h (62 mph, 54 kn) in rough or smooth air
Stall speed: 45 km/h (28 mph, 24 kn)
g limits: +4.0/-2.0
Maximum glide ratio: 13 at 52 km/h (32 mph; 28 kn)
Rate of sink: 1.10 m/s (217 ft/min) minimum, at 50 km/h (31 mph; 27 kn)
Crew: One

Lak LAK-12 / Sportline Aviacija LAK-12

The LAK-12 is a Lithuanian built single-seat FAI Open-class mid-wing sailplane with a one-piece forward-hinged canopy. The retractable main wheel rides on an oil/nitrogen shock absorber and uses a mechanical brake. A skid is used at the tail. The wings are glass-foam-glass construction and taper from a Wortmann FX67-K-170 airfoil inboard to an FX67- K-150 at the tips. Glidepath control is provided by double-panel upper surface airbrakes and by the flaps (-7, -4, 0, +5, +11, +15 deg). The wings are capable of holding a total of 190 liters of water in their leading edges and are filled and emptied through a hole in bottom of the fuselage.

Wing span: 20.42m / 67ft
Wing area: 14.63sq.m / 157.5sq.ft
Empty Weight: 360kg / 793.7lb
Payload: 290kg / 639.3lb
Gross Weight: 650kg / 1433lb
Wing Load: 29.5kg/sq.m / 6.05lb/sq.ft
Water Ballast: 190kg / 418.9lb
L/DMax: 47 at 51.3 kts / 95 km/h
MinSink: 0.48 m/s / 1.7 fps at 40.5 kts / 75 km/h
Aspect ratio: 28.5
Airfoil: Wortmann FX67-K-170 w/ FX67-K-150 tips
Seats: 1
Structure: Fiberglass / carbon fiber

Lak LAK-9 Lietuva / Sportline Aviacija LAK-9

The LAK-9 Lietuva (or Lithuania) single-seater Open Class sailplane was developed by LAK – Litovskaya Aviatsionnaya Konstruktsiya (or Lithuanian Aircraft Construction) from an earlier plastics sailplane, the BK-7, also named Lietuva, designed by Balis Karvyalis which made its first flight in December 1972. At this time the LAK factory was known as the Experimentalnii Zavod Sportivnoi Aviatsii (or Experimental Sports Aviation Factory), and a small experimental production batch of Lietuvas, designated BK-7A, was built and two of these participated in an international contest between Communist countries at Kishinev in April 1976. As a result of this competition a number of modifications were introduced in a developed version, the LAK-9, designed by Kestutis Gechas and which was then under construction; the prototype of this took part in the World Championships in Finland in June 1976 flown by O.Pasetsnik, but this particular aircraft withdrew from the last two days of the competition because of aileron damage.

The LAK-9 was the first Russian sailplane to compete in the World Championships since 1968 and at the time it was reported that the three LAK-9s then built had not, at that time, completed their flight testing. The type is now in production and the fourth series batch, begun in the winter of 1976-77, is reported to be designated LAK-9M (M for Modernised). The LAK-9 is a cantilever shoulder-wing monoplane of glassfibre/epoxy construction, with single-spar wings and provision of up to 397 lb of water ballast, and trailing edge flaps. The landing gear consists of a retractable monowheel and a tailwheel.

Span: 65 ft 8.25 in
Length: 23 ft 10.25 in
Height: 5 ft 0.25 in
Wing area: 161.35 sqft
Aspect ratio: 26.8
Empty weight: 842 lb
Max weight: 1,477 lb
Max speed: 130 mph (in rough air)
Max aero-tow speed: 87 mph
Min sinking speed: 1.67 ft/sec at 46 mph
Best glide ratio: 48:1 at 64 mph

Lak BK-7 Lietuva

The plastics BK-7 single-seater Open Class sailplane was developed by LAK – Litovskaya Aviatsionnaya Konstruktsiya (or Lithuanian Aircraft Construction), named Lietuva, designed by Balis Karvyalis, and made its first flight in December 1972. At this time the LAK factory was known as the Experimentalnii Zavod Sportivnoi Aviatsii (or Experimental Sports Aviation Factory), and a small experimental production batch of Lietuvas, designated BK-7A, was built and two of these participated in an international contest between Communist countries at Kishinev in April 1976. As a result of this competition a number of modifications were introduced in a developed version, the LAK-9.

Lamprecht-Gerstel Eindecker

Built by the fitter Eugen Lamprecht and engine mechanic Heinrich Gerstel in Pforzheim in 1909. Lamprecht was the initiator of the project with Gerstel to install the engine. When funds ran out, the machine was exhibited at the guest house “Schwarzer Adler”, where it is told that the engine was occasionally started inside the ball room. Afterwards the monoplane was tested at the Exerzierplatz Forchheim, with only minor success.

Lamson PL-1 Quark

Philip Lamson designed and built the single-seat PL-1 Quark in 1964 as a lighthearted experimental aircraft project to create a prone position-pilot glider. To this end the pilot was accommodated lying down with his head in the nose bubble.

The PL-1 is constructed from fiberglass, with the wings made from a balsa-fiberglass sandwich that was laid up in a female mold. The wing was originally of 20 ft (6.1 m) span, but this was quickly increased to 30 ft (9.1 m) with tip extensions and finally the aircraft received a new 40 ft (12.2 m) three-piece wing. The airfoil was an Irv Culver modification to the NACA 0012. The landing gear was a monowheel, with small wing tip skids.
Soaring Magazine described the aircraft as “purely a lark and a quirky lark at that”. The designer described the performance as “somewhere between a Nimbus and a Rogallo”.

Only one Quark was built and it was registered with the US Federal Aviation Administration in the Experimental – amateur-built category.

The aircraft logged about 300 hours in its 30 ft (9.1 m) wingspan version. The Quark was removed from the FAA registry on 13 August 2002 and the aircraft likely no longer exists.

Length: 10 ft (3.0 m)
Wingspan: 40 ft (12 m)
Wing area: 88.89 sq ft (8.258 sq.m)
Aspect ratio: 18:1
Airfoil: Irv Culver modification to the NACA 0012
Empty weight: 340 lb (154 kg)
Gross weight: 504 lb (229 kg)
Crew: one
Wing loading: 5.67 lb/sq ft (27.7 kg/sq.m)

Lambie Hang Loose

In 1972 a guy named Jack Lambie wrote an article for Soaring magazine and published a set of plans on “how to build your own Chanute-style hang glider”. He called his design “Hang Loose” (hey it was the 70’s 😉

Experience:
When I saw that article, I knew instantly I had to build one. I can remember sketching ideas for such craft since I was in 5th grade. So I ordered the plans Carleton and I built one. On one of the days of testing we happened to get photographed and interviewed by the local newspaper. (I think the reporter was just happening by at the time)

We had to make some changes to the design: for one thing we could not get bamboo to make the ribs. Instead I cut them out of 1/8″ plywood, about 1″ thick top to bottom and mounted the ends between two pine blocks. Heavier than the bamboo but a better fit to the shape for sure.

We also could not get the yellow pine that was suggested and used spruce I think, but it had some very small knots in it that did cause a problem at one point. (Spar failure in flight!)

At the time, I already had a sailplane pilot’s license (you can solo at 14 and it was cheaper than flying power planes) and of course I had flown a lot of model airplanes, so I was elected the test pilot. You can see me in that photo with my leg out to move the CG (centre of gravity) forward a bit.

The angle of the tail was not set properly so I could not get the angle of attack enough and basically just fell down with the thing. After fixing that back at Carleton’s house (right across from the field in the picture) it worked great. We both flew it many times down a little 20′ grassy drop-off.

The feeling of the glider lifting you up as it gained speed was AWESOME.

You could not really turn the thing at all…too much stability in roll. We talked about adding some tip-dragger rudders or ailerons but the flight times were short enough you didn’t really need any left – right steering.

We had a few snafus but by never flying higher than it was safe to fall we didn’t get hurt. Spectators would offer to hook us up to their cars with a rope and and tow us …but we were too smart for that 😉

Lambert The Major Lambert / R-266

The Lambert R-266 features a solid master connecting rod and two piece crankshaft. A two piece magnesium alloy crankcase, split on the cylinder centreline, is held together with ten bolts. The front section carries the front main ball-bearing and thrust ball-bearing. The inlet passage and valve lifter guides are cast in the rear section.

Cylinder barrels are nickel semi-steel castings. Removable cylinder hads of aluminium alloy with exhaust and inlet ports toward the rear, are held in place with four long studs which run through the crankcase. Enclosed valve actuating mechanism is at the rear of the cylinders.

Accessories and their drives are grouped at the rear making for easy cowling.

Equipment incules a propeller hub, exhaust ring, carburettor air heater and muffler, tool kit, and instruction and parts book.

Type: 5 cylinder air cooled, fixed radial
Dept of Commerce Rating: 90 hp at 2375 rpm
Displacement: 266 cu.in
Compression ratio: 5.55-1
Bore: 4 1/4 in
Stroke: 3 3/4 in
Length: 30 3/8 in
Diameter: 33 in
Weight: 214 lb
Fuel consumption: not more than .55 lb/hp/hr
Oil consumption: not more than .025 lb/hp/hr
Lubrication: Pressure and dry sump
Ignition: Dual Scintilla
Carburation: Stromberg NAR 3
Spark plugs: 2 per cylinder Champion